Runoff and Sediment Yield Variations in Response to Precipitation Changes: A Case Study of Xichuan Watershed in the Loess Plateau, China

Water 2015, 7, ; doi: /w Article OPEN ACCESS water ISSN Runoff and Sediment Yield Variations in Response to Precipitation Changes: A Case Study
of 19
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Water 2015, 7, ; doi: /w Article OPEN ACCESS water ISSN Runoff and Sediment Yield Variations in Response to Precipitation Changes: A Case Study of Xichuan Watershed in the Loess Plateau, China Tianhong Li 1,2, * and Yuan Gao 1,2 1 College of Environmental Sciences and Engineering, Peking University, Beijing , China; 2 Key Laboratory of Water and Sediment Sciences, Ministry of Education, Beijing , China * Author to whom correspondence should be addressed; Tel.: Academic Editors: Yingkui Li and Michael A. Urban Received: 22 August 2015 / Accepted: 13 October 2015 / Published: 19 October 2015 Abstract: The impacts of climate change on hydrological cycles and water resource distribution is particularly concerned with environmentally vulnerable areas, such as the Loess Plateau, where precipitation scarcity leads to or intensifies serious water related problems including water resource shortages, land degradation, and serious soil erosion. Based on a geographical information system (GIS), and using gauged hydrological data from 2001 to 2010, digital land-use and soil maps from 2005, a Soil and Water Assessment Tool (SWAT) model was applied to the Xichuan Watershed, a typical hilly-gullied area in the Loess Plateau, China. The relative error, coefficient of determination, and Nash-Sutcliffe coefficient were used to analyze the accuracy of runoffs and sediment yields simulated by the model. Runoff and sediment yield variations were analyzed under different precipitation scenarios. The increases in runoff and sediment with increased precipitation were greater than their decreases with reduced precipitation, and runoff was more sensitive to the variations of precipitation than was sediment yield. The coefficients of variation (CVs) of the runoff and sediment yield increased with increasing precipitation, and the CV of the sediment yield was more sensitive to small rainfall. The annual runoff and sediment yield fluctuated greatly, and their variation ranges and CVs were large when precipitation increased by 20%. The results provide local decision makers with scientific references for water resource utilization and soil and water conservation. Water 2015, Keywords: SWAT model; precipitation; runoff; sediment yield; simulation; the Xichuan River; the Loess Plateau 1. Introduction Climate change as a result of both natural factors and human activities is altering the earth s hydrologic cycles to various degrees [1,2]. Climate change affects hydrology mainly through changes in precipitation, temperature, and evaporation [3,4], and it subsequently influences the temporal-spatial distributions of runoff and sediment, as well as the patterns of runoff and sediment transport [5]. The impacts of climate change on water resources and the hydrologic cycles have long been a focus of the international community [6,7]. Research on this issue began as early as the 1980s. In 1985, the World Meteorological Organization (WMO) published a summary report of their study of the impacts of climate change on hydrology and water resources and proposed several evaluation and test methods. In 1987, the WMO proposed analyzing the sensitivity of hydrology and water resources to climate change. This issue was also discussed in the 2007 international conference of the International Union of Geodesy and Geophysics (IUGG). The Intergovernmental Panel on Climate Change (IPCC) of the United Nations analyzed the impacts of climate change on hydrology and water resources from 1990 to In its technical report [8], the IPCC highlighted that the global and regional water resource problems caused by climate change are crucial issues. Changes in precipitation and temperature have significant effects on runoff and water availability, particularly in semiarid and arid regions [9]. China has always considered the impacts of climate change on water resources to be important and has actively carried out a series of scientific studies to support research on the impact of the changing environment (due to global changes and human activities) on water cycles [5,10]. For instance, the National Planning Outline for Mid- and Long-term Scientific and Technological Development ( ) issued by the State Council of China in 2006 pointed out that research on the impacts of global climate change in China is a focus, with special emphasis on the impacts of climate change on hydrologic cycles and regional water resources, especially in arid regions with fragile ecological environments [11]. Currently, studies of the impacts of climate change on runoff and sediment mainly focus on two aspects. Some studies analyze the changes in the temporal-spatial distributions of runoff and sediment and the patterns of runoff and sediment transport that are caused by changes in climate factors, such as precipitation and temperature, whereas other studies analyze the trends of the changes in runoff and sediment under future climate change scenarios. The main method for quantitatively evaluating and studying the impacts of climate change on runoff and sediment is to use watershed hydrological models. The most commonly used models are statistical regression models, water balance models, and distributed physical models [9,12]. Of these models, the Soil and Water Assessment Tool (SWAT) [13], which was developed by the US Department of Agriculture in the 1990s, has been widely applied to watersheds around the world [14 20]. There are two types of predicted future climate change scenarios. First, changes in temperature, precipitation, and evaporation are hypothesized based on the trends and ranges of the meteorological changes in the study area, as well as specialized knowledge, experience, and the time-series Water 2015, statistical analysis method, which is easy to design and apply [21 23]; Second, different climate change scenarios can be simulated using models, such as the General Circulation Models [19,24]. Previous studies have shown that the precipitation in the Yellow River Basin has decreased significantly since the 1970s [10,25] although variation trends may differ in sub-basins. Precipitation is the main source of runoff and one of the driving factors of soil and water losses in the Loess Plateau [26,27], where water resources are scarce. Therefore, in the context of global climate change, studying the impacts of changes in precipitation on the runoff and sediment production in the Yellow River Basin is important for the sustainable utilization of water resources. Most previous studies of the impacts of changes in precipitation on water resources in the Yellow River Basin have focused on the entire basin [28,29] or the basin at relatively large scales [30 32]. Relatively few studies have focused on small watersheds. In addition, most studies have focused on the impact of precipitation on the runoff and have rarely investigated the impact of precipitation on the sediment yield. In fact, high sediment content is an important and unique characteristic of the rivers in the Loess Plateau, China. Sediment transport requires a considerable amount of water [33] and competes with other water uses. Thus, it is imperative to consider sediment when studying the water resource problems of these rivers. This study used the Xichuan Watershed, a typical small basin in the hilly and gully area in the Loess Plateau, as a target area, and used ArcGIS, MATLAB, and SPAW [34,35] to process observed meteorological and hydrological data. Then, a localized SWAT model was constructed, calibrated, and validated. Using the SWAT model under different precipitation scenarios, the study quantitatively predicted the impacts of changes in precipitation on the runoff and sediment yield in this small watershed and analyzed the characteristics of the changes in runoff and sediment production with the aim of providing a scientific basis for the management and sustainable utilization of water resources in basins that are similar to the study area. 2. Methodology Based on the spatial and attribute data, including meteorological data, hydrological data, soil map, land use map, and a digital elevation model (DEM), this study investigated the characteristics of the changes in the precipitation, runoff, and sediment yield in the study area. Spatial and attribute databases of the SWAT model were developed. After determining the parameters of the SWAT model and verifying the predicted results from the model, we quantitatively analyzed the impacts of changes in precipitation on the runoff and sediment production in the study area using precipitation change scenarios. Figure 1 shows the technical workflow of the study. This study used AVSWAT, developed by integrating the SWAT into ArcView for the analysis. AVSWAT has powerful spatial analysis and processing functions and is convenient to use. The SWAT model consists of three sub-models: the hydrological process sub-model, the soil erosion sub-model and the pollution load sub-model. This study mainly uses the hydrological process and the soil erosion sub-models. Water 2015, Study Area Figure 1. Technical workflow of this study. The Xichuan River is a tributary of the Yanhe River (a tributary of the Yellow River) with a total length of 61.5 km. The Xichuan Watershed is located west of the Yanhe River Basin between E and E and between N and N, covering an area of 801 km 2 [36]. The mean runoff of the watershed was m 3 from 2001 to The river originates in Caofeng Village, Zhidan Town in Zhidan County and flows past Xihekou Village, Zhuanyaowan Town and Gaoqiao Village in Ansai County and Zaoyuan Village in the Baota District and eventually flows into the Yanhe River near Shifogou in the Baota District. The Zaoyuan Hydrological Station (ZHS) is located 13 km upstream from the mouth of the Xichuan River, and it controls 90% area (719 km 2 ) of the whole watershed (Figure 2). The Xichuan Watershed has a continental monsoon climate where winters are cold and dry with little precipitation, whereas summers are warm with abundant precipitation. Precipitation is unevenly distributed and mainly concentrated in the summer and fall, accounting for 54.3% and 27.7% of the total annual precipitation. Floods in this watershed have relatively short durations, rising and falling suddenly with high sediment concentrations [37]. The soil types in this watershed include yellow loessial soil, red clay soil, alluvial soil, and dark loessial soil. The yellow loessial soil, developed from the parent loess, is the main soil type, covering more than 80% of the total basin area. The vegetation coverage of the watershed is very low, belonging to the forest steppe zone. Both natural and artificial vegetation types are present, mainly consisting of crops, evergreen coniferous forests, deciduous coniferous forests, deciduous broad-leaved forests, shrubs, and grasslands. Water 2015, Figure 2. Location of the study area. More than 80% of the basin area suffers soil erosion by water. The multi-year mean sediment discharge is t/a. Since the 1970s, a series of water and soil conservation and ecological construction projects have been implemented and have substantially improved the ecological environment in the watershed [38] Data and Data Preprocessing The main data used in this study included Digital Elevation Model (DEM) data, a land use map, a soil type map, precipitation data, temperature data, and the boundary of the Yanhe River basin. Table 1 lists the data descriptions and sources. Table 1. List of data that were used in this study. Data Type Temporal/Spatial Resolution Source DEM data Grid format, 30 m/grid Land use map At the scale of 1:100,000, compiled at 2005 Soil type map At the scale of 1:1,000,000, compiled at 2005 Meteorological data Runoff and sediment yield Daily precipitation, daily maximum temperature and daily minimum temperature between 1990 and 2010 Monthly runoff and sediment yield between 2001 and 2010 Data Application Environment Sharing Platform of the Chinese Academy of Sciences Data Application Environment Sharing Platform of the Chinese Academy of Sciences Data Application Environment Sharing Platform of the Chinese Academy of Sciences China Meteorological Data Sharing Service Website The Zaoyuan Meteorological Station in the Yan an City The data required for the SWAT model included geospatial data, a non-spatial attribute database, meteorological data, and hydrological and sediment data for model calibration and verification. Spatial data processing, grid calculations, and interpolations were conducted using ArcGIS, and the statistical Water 2015, analysis was performed using Excel. All spatial data used in the SWAT were converted to the Albers equal-area conic projection. The whole area was divided into 31 sub-basins using the DEM and each sub-basin contained 5 16 hydrological response units (HRUs), which is the basic unit in SWAT model SWAT Model Development Model Construction The SWAT model requires the land use classification scheme developed by the US Geological Survey (USGS). It also requires the auxiliary land use attributes with parameters provided by the USGS. The land use map used in this study had to be reclassified to meet these requirements. After reclassification, the main land use types included farmland (39.30%), typical grassland (32.60%), meadow grassland (13.09%), deciduous coniferous forest and deciduous broad-leaved forest (8.90%), bush wood (5.05%), evergreen forest (0.86%), barren land (0.09%), water body (0.05%), and rural villages (0.05%) [35]. The soil data included the spatial distribution and physical and chemical attributes of the soils. The soil map was produced based on the 2005 soil survey of the study area. The physical attributes of the soils mainly included the thicknesses, silt contents, clay contents, bulk densities, organic carbon contents, effective water contents, saturated hydraulic conductivities, and the available field capacities. These attributes control the movement of the water and air in the soil and have an important role in the water cycles. This study established a users soil parameter database based on these characteristics. The soils were divided into four hydrologic groups. For the same precipitation and surface conditions, soils with similar runoff production capacities were classified into a single hydrologic group [39]. The wet density of a soil, the available effective water in a soil layer and the saturated hydraulic conductivity coefficient can be calculated using the SPAW model [34,35]. The SPAW model is a daily hydrologic budget model for agricultural fields. It also includes a routine for the daily water budgets of inundated ponds and wetlands that utilizes the field hydrology of the watershed. The soil erosion factor (K) is often used to evaluate soil erodibility. K is calculated based on the organic carbon and particle compositions of the soil using the method proposed by Williams [40]. The observed meteorological input data mainly included the precipitation, daily maximum and minimum temperature data from 2001 to The SWAT model includes a built-in weather generator. If some data were not available, the weather generator simulated daily meteorological data based on multi-year monthly mean data that were provided in advance. The pcpstat and dew02 procedures were used to calculate daily precipitation and temperature to obtain the related parameters and generate the weather data that were needed for simulations. The measured runoff and sediment data were collected at ZHS (Figure 2) from 2001 to They were used in sensitivity analysis and parameters calibration. The measured daily precipitation data were used to simulate daily runoff using the Soil Conservation Service (SCS) curve method [39]. The potential evaporation was derived using the Penman-Monteith method [41]. The variable storage coefficient method [42] was used in the river channel routing simulation. Water 2015, Sensitivity Analysis, Validation, and Testing of the SWAT Parameters The parameter sensitivity analysis module was used to analyze the sensitivities of the parameters in the runoff and sediment simulations. This module uses the Latin hypercube one-factor-at-a-time (LH-OAT) method [43]. The objective of this analysis is to analyze and determine which input parameters have the most significant impacts on the output when their values are changed. Important parameters are selected to highlight their impacts on the simulation and to reduce the time that is needed for parameter adjustment. In this study, the simulated runoff and sediment yield were compared with actual gauged data at ZHS (Figure 2). The important factors affecting the precision of the simulation in the watershed were determined after analyzing the sensitivity of each parameter. The runoff and sediment yield parameters were calibrated in sequence. Three indexes, including the relative error (Re) [44], the coefficient of determination (R 2 ) [45] and the Nash-Sutcliffe coefficient (Ens) [46] were chosen to statistically test the accuracy of the calibrated and validated runoff and sediment yield outputs. If Re = 0, the model prediction is the same as the observed data. If Re 0, the model prediction is larger than the observation. If Re 0, the model prediction is less than the observed value. R 2 was obtained from the linear regression in Microsoft Excel. The larger the R 2 value, the better simulation of the model. If the value of Ens is greater than 0.75, the simulation is excellent. If Ens is between 0.36 and 0.75, the simulation is satisfactory, and if Ens is less than 0.36, the simulation is unsatisfactory Precipitation Scenarios Based on land use maps in 2005 and the climate conditions from 2001 to 2010, the calibrated and verified SWAT model was used to simulate the impacts of precipitation on the runoff and sediment yield by altering the input climate conditions (precipitation). Spatial variability in precipitation was not considered in the simulations because the study area is a small watershed with limited precipitation stations. Precipitation scenarios were determined based on the variation characteristics of the precipitation in this area. During the study period, the annual precipitation did not show significant increasing or decreasing trend in this area. A previous study [47] also showed no significant increasing or decreasing trend in the Yanhe River basin. The mean annual precipitation in the study area from 2001 to 2010 was 514 mm. Thus, we considered four precipitation change scenarios: (1) the annual mean precipitation increases by 20%, i.e., 617 mm; (2) the annual mean precipitation increases by 10%, i.e., 565 mm; (3) the annual mean precipitation decreases by 10%, i.e., 462 mm; and (4) the annual mean precipitation decreases by 20%, i.e., 411 mm Variance Analysis The coefficient of variation (Cv) was used to reflect the inter-annual changes in the precipitation and runoff. It is calculated using the following equation: = (1) Water 2015, where SD is the standard deviation of a variable and M is the average value of the variable. The greater the value of Cv of precipitation or runoff, the greater the extent of the inter-annual change in the precipitation or runoff is, and the possibility of occurrences of floods or droughts increases. The smaller the value of Cv of the inter-annual precipitation or runoff is, the smaller the extent of the inter-annual change in the precipitation or runoff is, which is more beneficial to the utilization of water resources. Cv also reflects the characteristics of the inter-annual change in the sediment yield. The greater the value of Cv of the sediment yield indicates that the sediment yield changed greatly, and disasters such as soil erosion are more common. On the other hand, the smaller the value of Cv of sediment yield is, the smaller changing extent of the sediment yield is, which is more beneficial to water and soil conservation. The changing rate (CR)
Related Search
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks

We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

More details...

Sign Now!

We are very appreciated for your Prompt Action!