Mobile

EB9263 Evaluation Board PM9263 CPU Module User Manual

Description
Evaluation Board PM9263 CPU Module User Manual Version 1.2 embedded development tools Acknowledgements November, 2010 Ronetix has made every attempt to ensure that the information in this document is accurate
Categories
Published
of 11
121
Categories
Published
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Share
Transcript
Evaluation Board PM9263 CPU Module User Manual Version 1.2 embedded development tools Acknowledgements November, 2010 Ronetix has made every attempt to ensure that the information in this document is accurate and complete. However, Ronetix assumes no responsibility for any errors, omissions, or for any consequences resulting from the use of the information included herein or the equipment it accompanies. Ronetix reserves the right to make changes in its products and specifications at any time without notice. Any software described in this document is furnished under a license or non-disclosure agreement. It is against the law to copy this software on magnetic tape, disk, or other medium for any purpose other than the licensee's personal use. Ronetix GmbH Waidhausenstrasse 13/ Vienna Austria Tel: Fax: Internet: Acknowledgments: ARM, ARM7, ARM9 and Thumb are trademarks of ARM Ltd. Windows, Win32, Windows CE are trademarks of Microsoft Corporation. All other trademarks are trademarks of their respective companies RONETIX All rights reserved. 2 Contents 1 OVERVIEW Scope Package contents THE CPU MODULE PM The PM Electrostatic Warning Layout Circuit Description AT91SAM Revisions pin SODIMM Connector Memories Serial Number Chip DS Crystal Quartzes Power Ethernet Controller Temperature range BASE BOARD BB Jumpers Electrostatic Warning Requirements GETTING STARTED Getting started with Linux Getting started with a standalone example under Windows DIFFERENCES BETWEEN PM9263 AND ATMEL AT91SAM9263-EK 1 Overview 1.1 Scope The EB9263 Development Kit enables real time code development and evaluation. It supports AT91SAM Package contents The Development Kit consists of: - CPU Module PM Base Board BB Power Supply 5V/1A - PEEDI JTAG Emulator and Flash Programmer (optional) - DVD including software, datasheets and documentation A copy of the DVD can be found here: 2 The CPU Module PM The PM9263 The PM9263 from Ronetix consists of an AT91SAM9263 together with several peripherals: ATMEL AT91SAM9263 Microcontroller in BGA324 package with: ARM926EJ-S ARM Processor 4 DSP Instruction Extensions ARM Jazelle Technology for Java Acceleration 16 Kbytes Data Cache, 16 Kbytes Instruction Cache, Write Buffer 220 MIPS at 200 MHz Bus Matrix Five Masters and Five Slaves Embedded ICE (In-Circuit Emulation) with JTAG interface 80 Kbytes Internal RAM Dual External Bus Interface DMA Controller 3 USARTs 2 Synchronous Serial Controllers (SSC) Two Master/Slave SPI Interfaces One 3-Channel 16-bit Timer/Counter Programmable Watchdog Timer USB 2.0 Full Speed (12 Mbits/s) Host Port USB 2.0 Full Speed (12 Mbits/s) Device Port LCD Controller 2D Graphics Accelerator Image sensor interface AC97 Controller Real-time Clock with On-chip 32 khz Oscillator 160 Programmable I/O Lines Advanced Power Management Controller 4 Mbyte 16-bit NOR Flash 64 Mbyte 32-bit SDRAM 4 MB PSRAM connected on the EBI1 2 Gbit NAND Flash 32 Mbits SPI Serial DataFlash AT45DB321D Serial Number Chip DS2401 SODIMM 200-pin connector Dimension 67,6 mm x 40.0 mm 2.2 Electrostatic Warning The PM9263 Module is shipped in protective anti-static packaging. The board must not be subjected to high electrostatic potentials. A grounding strap or similar protective device should be worn when handling the board. Avoid touching the component pins or any other metallic element. 5 2.3 Layout The board layout diagram (Figure 2-1 and Figure 2-2) shows an approximate floorplan of the board. It was designed to provide the smallest board dimensions. The board has 6 signal layers and 2 power planes. The mechanical drawing of the CPU module is available on the DVD or here: Figure 2-1 Top View Figure 2-2 Bottom View 6 2.4 Circuit Description The schematic of the CPU module can be found on the DVD or here: AT91SAM9263 The footprint is for a 324-pin BGA package Revisions There are two revisions of PM9263: v1.0 and v1.1. The differences between both versions are: - PM9263 v1.0 fits into 1.8V and 2.5V SODIMM200 connectors, whereas PM9263 v1.1 fits only in 2.5V connectors. - V1.1 PB20 and PB21 can be used for version coding - V1.1 supports NAND Flash devices with up to four dies - PB23, PB24, PB25 are used for NAND_CS1, NAND_CS2 and NAND_CS3 - V1.1 PB27 is used to enable or disable the 50MHz quartz oscillator - V1.1 - Removed 16-bit NAND Flash footprint - V1.1 supports up to 512Mbit NOR Flash devices - V1.1 doesn t use pin 200 of SODIMM200 connector pin SODIMM Connector The 200-pin SODIMM connector makes the most CPU pins, Vcc 3.3V and Ground available to the user. The recommended SODIMM V connector is: FCI FSLF Memories The PM9263 has on board: 4 Mbyte, 16-bit Parallel Flash (boot capable) 64 Mbyte, 32-bit SDRAM 4 Mbyte PSRAM connected to EBI1 2 Gbit, 8-bit NAND Flash (boot capable) 32 Mbit, serial SPI DataFlash (boot capable) The AT91SAM9263 CPU can boot in 2 different ways: - If BMS = 0 - direct from the parallel Flash - If BMS = 1 then the internal 32 KB ROM boot loader of AT91SAM9263 allows the CPU to boot from the DataFlash or the NAND Flash The JTAG Emulator and Flash Programmer PEEDI from Ronetix support the flash programming of all these memories: FLASH, DataFlash and NAND Flash. For more information visit 7 2.4.5 Serial Number Chip DS2401 The DS Wire Silicon Serial Number has a unique 48-bit serial number, an 8-bit CRC, and an 8-bit Family Code. It is connected to PB31 of the AT91SAM9263 and allows the module to have a unique serial number. It can be used also for the MAC address of the Ethernet controller Crystal Quartzes The board has two crystals and one oscillator: a khz connected to the RTC low-power oscillator of the AT91SAM9263, an MHz connected to the main oscillator and a 50 MHz oscillator for the Ethernet Controller. The 50MHz oscillator can be enabled or disabled with a GPIO: PB27 The AT91SAM9263 Master Clock can be derived from the khz crystal quartz or the MHz crystal quartz depending on the programming of the APMC registers Power PM9263 v1.0 requires only 3.3V power supply. Pin 200 of the SODIMM200 connector is connected to +5V on the base board, but for custom designs this is not necessary pin 200 can be connected to +3.3V. PM9263 v1.1 doesn t use pin 200 it is not used and not connected. The power consumption of PM9263 with all peripherals without Ethernet is 200mA/3.3V. The power consumption of PM9263 with all peripherals with Ethernet is 300mA/3.3V Ethernet Controller The PM9263 has on board a DP /100M PHY Temperature range PM9263 is available in two temperature ranges: - Standard temperature range C - Industrial temperature range C 8 3 Base Board BB9263 The BB9263 is equipped with: - SODIMM 200 pin for reception of PM one USB device port - two USB Host ports - one RJ45 10/100M Ethernet - JTAG debug interface, 20-pin - one 3.5 ¼ VGA TFT LCD + Touch Screen 40 pin - Image interface, 30 pin - two RS232 - four Audio connectors: Line In, Line Out, Headphone, Microphone - one MMC/SD card connector - one Compact Flash connector 9 - CAN connector - expansion connectors - one reset push-button - one wakeup push-button - two user input push-buttons - three general purpose LEDs - two power LEDs: one for 5V and one for 3.3V - one Lithium Coin Battery - DC power connector 2.1mm by 5.5mm. The central pin is positive polarity. The board dimension is 145 mm by 145 mm 3.1 Jumpers Jumper J19 J20 J21 J22 Description Connect/Disconnect the 3.0V battery backup. default: open Forces power on. To use the software shutdown control, J20 must be opened and the battery backup J19 must be closed. default: close Boot mode select: open the CPU boots from the internal ROM close the CPU boots from the NOR Flash default: close Enable 120 ohms CAN bus resistance termination default: open 3.2 Electrostatic Warning The BB9263 Module is shipped in protective anti-static packaging. The board must not be subjected to high electrostatic potentials. A grounding strap or similar protective device should be worn when handling the board. Avoid touching the component pins or any other metallic element. 3.3 Requirements The BB9263 requires DC power supply 5V / 1A. The DC power connector is 2.1mm by 5.5mm; the central pin is positive polarity. The board has reverse voltage protection. For more information please see the board schematics on the DVD. 10 4 Getting started The EB9263 is delivered with a DVD containing all necessary and step-by-step procedure for working with the GNU development tools. Please refer to this DVD, or to the Ronetix web site, for the most up-to-date information: 4.1 Getting started with Linux To get started with U-BOOT and Linux, please read the U-BOOT and Linux Kernel readme from the DVD or from here: 4.2 Getting started with a standalone example under Windows To get started with a standalone example under Windows, please read the Software Installation Guide from the DVD or from here: 5 Differences between PM9263 and Atmel AT91SAM9263-EK AT91SAM9263-EK Quartz Oscillator MHz MHz Signal NAND Ready/Busy PA22 PB30 LCD CONTROL IN (PIN35) PA30 PA22 PM9263 EtherPHY Davicom DM9161A National DP83848 LEDs PC29, PB8, PB7 PB7,PB8 Boot Memory DataFlash, NAND NOR, DataFlash, NAND Touchscreen SPI0_NPCS3-PB11 SPI0_SPCK-PA2 SPI0_MOSI-PA1 SPI0_MISO-PA0 MMC Card Detect PE18 PA21 MMC Write Protect PE19 PA16 SPI1_NPCS0-PB15 SPI1_SPCK-PB14 SPI1_MOSI-PB13 SPI1_MISO-PB12 11
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks
SAVE OUR EARTH

We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

More details...

Sign Now!

We are very appreciated for your Prompt Action!

x