Mechanical performances of surface modified jute fiber reinforced biopol nanophased green composites

Mechanical performances of surface modified jute fiber reinforced biopol nanophased green composites
of 7
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
  Mechanical performances of surface modified jute fiber reinforced biopolnanophased green composites Mohammad K. Hossain ⇑ , Mohammad W. Dewan, Mahesh Hosur, Shaik Jeelani Tuskegee University Center for Advanced Materials (T-CAM), Tuskegee University, 101 Chappie James Center, Tuskegee, AL 36088, USA a r t i c l e i n f o  Article history: Received 5 January 2011Received in revised form 1 March 2011Accepted 21 March 2011Available online 9 April 2011 Keywords: A. Polymer–matrix composites (PMCs)B. InterfaceB. Mechanical propertiesE. Compression moulding a b s t r a c t Surface modification of jute fibers was accomplished by performing chemical treatments, includingdetergent washing, dewaxing, alkali, and acetic acid treatment. Morphology of modified surfaces exam-ined using scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR)revealed improved surfaces for better adhesion with matrix. Enhanced tensile properties of treated fiberswere obtained from fiber bundle tensile tests. Using solution intercalation technique and magnetic stir-ring, 2%, 3%, and 4% by weight Montmorillonite K10 nanoclay were dispersed into the biodegradablepolymer, biopol. Jute fiber reinforced biopol biocomposites with and without nanoclay manufacturedusing treated and untreated fibers by compression molding process showed almost the same volumefraction for all the samples. However, the lower void content was observed in the surface modifiedand nanoclay infused jute biopol composites. Mechanical responses of treated fiber reinforced biopolcomposites (TJBC) without nanoclay evaluated using dynamic mechanical analysis (DMA) and flexuretests showed 9% and 12% increase in storage modulus and flexure strength, respectively, compared tountreated jute fiber reinforced composites (UTJBC). The respective values were 100% and 35% for 4%nanoclay infused TJBC, compared to UTJBC without nanoclay. Lower moisture absorption and bettermechanical properties were found in the nanophased composites even after moisture conditioning.   2011 Elsevier Ltd. All rights reserved. 1. Introduction Manufacturing of synthetic fiber composites not only consumehuge energy but also their disposal at the end of the life cycle isvery difficult since there is virtually no recycling option. Hence,the biocomposite industry is developing at a significant pace tomeet growing consumer awareness and follow new environmentalregulations [1]. Lignocellulosic bio-fibers derived from leaf, bast, fruit, grass or cane contribute to the strength of bio as well as syn-thetic polymer composites in various applications [2].Elements of jute fibers are cellulose, hemicelluloses, lignin, andpectin. Cellulose is the main element of jute fiber, which is resis-tant to alkali but hydrolyzed in acid. Hemicellulose works as sup-porting matrix agents of cellulose. Hemicellulose is hydrophilic,soluble in alkali, and easily hydrolyzed in acids. Lignins are amor-phous and hydrophobic in nature. They contain aromatic and ali-phatic constituents. Pectins are like waxes that provide plantflexibility [3]. Jute, like other lignocellulosic fibers, consists of  A OH group, which therefore causes it to be susceptible to moistureand directly impairs the properties of jute composites, especiallydimensional stability. These natural fibers do not efficiently adhereto non-polarmatrices due to this polar group. To overcomethis dif-ficulty, these fibers should be modified chemically or physically[4]. Chemically modified surfaces decrease moisture absorption,and increase tensile strength [5,6] and wettability of fibers by ma-trix [7].Various research groups have worked on biodegradable poly-meric materials, such as bionolle, biopol, poly(3-hydroxybutyrate)(PHB)andpolylacticacid(PLA)[8],touseinnaturalfiberreinforced composites. However, PHB and biopol can be considered as truebiopolymersbecausetheyaresynthesizedbybacteriaasmacromol-ecules. The remaining biodegradable polymers are synthetic of semi-synthetic [9]. The homopolymer poly(3-hydroxybutyrate)(PHB) is brittle in nature and has narrow processability window,compared to the conventional plastics. To overcome these draw-backs, 3-hydroxyvalerates are added with PHB to prepare copoly-mers. PHB and its copolymers are highly crystalline and have ameltingpoint,strength,andmoduluscomparabletothoseofisotac-tic polypropylene [10].Moisture barrier, flammability resistance, thermal, andmechanical properties of polymeric composites can be improvedby adding a small amount of nanoclay as filler particles [11]. Nano- clay agglomerates into the composites due to improper dispersion.A stabilization process is used to remove larger clay agglomeratesin the nanoclay suspension [12]. 1359-8368/$ - see front matter    2011 Elsevier Ltd. All rights reserved.doi:10.1016/j.compositesb.2011.03.010 ⇑ Corresponding author. Tel.: +1 334 727 8128; fax: +1 334 724 4224. E-mail address: (M.K. Hossain).Composites: Part B 42 (2011) 1701–1707 Contents lists available at ScienceDirect Composites: Part B journal homepage:  Saha et al. showed 65% enhancement in tensile strength of jutefibers by alkali-steam treatment [13]. Zini et al. found that surface acetylation of the flax fiber promotes fiber–matrix interaction andimproves the mechanical properties of the flax fiber–biopol com-posites [8]. Corrales et al. used fatty acid derivate for the chemical modification of jute fibers [4]. Doan et al. used maleic anhydride grafted polypropylene (PP) as a coupling agent in jute-PP compos-ites and showed better tensile properties by matrix modification[1]. Hong et al. used silane for the surface modification of jute fiberto improve the interfacial interaction between jute fibers and poly-propylene matrix [14]. Mohanty et al. showed that alkali treatment and low grafting of acrylonitrile (AN) resulted in better mechanicalproperties in jute–biopol composites [15]. Vilaseca et al. found in- creased strength and stiffness in the NaOH treated jute-starchcomposites compared to untreated jute composites [16]. Bledzki et al. evaluated the mechanical performance of man-made naturalfiber reinforced PP/PLA/PHBVcompositesandfound improvementsin impact and tensile strength [17]. Reddy et al. observed about 25 MPa maximum flexural strength in the completely biodegrad-able syprotein-jute biocomposites [18]. Sing et al. fabricated wood/bamboo fiber reinforced PHBV composites using extrusionfollowed by injection molding process and the highest flexuralstrength was observed to be 31.09 MPa in the wood-PHBV com-posites [19]. Jawaid et al. evaluated chemical resistances, void con- tent, and tensile properties of the epoxy-based trilayer oil palm- jute composites and found better properties [20]. Hu et al. studiedthe effect of coating on jute-PLA composites and observed lowermoisture absorption and better tensile properties using adhesivetape coating [21]. Xie et al. evaluated the effect of nanosilica inthe PHBV and found improved toughness and stiffness with 1% sil-ica loading [22]. Huang and Netravali observed better tensile and flexural properties in flax fibers/soyprotein-nanoclay green com-posites compared to conventional composites [12].To the authors’ best knowledge, no study was reported in theopen literatures performed on the jute-based nanocomposites thatare 100% biodegradable. Hence, the objective of this study is to de-velop a 100% biodegradable jute-based nanocomposite for struc-tural applications. Jute fibers were chemically treated with amodified 4-step process for better interfacial adhesion with matrixand evaluated the treated fibers by FTIR, SEM, and tensile tests.Treated/untreated jute fiber–biopol biocomposites with/withoutnanoclay were manufactured using compression molding processand their mechanical performance was studied through DMA,moisture absorption, and flexure tests. 2. Experimental  2.1. Materials Poly(3-hydroxybutyrate-co-3-hydroxyvalerate-12%)-Biopolymergranule (Biopol) obtained from Goodfellow Cambridge Ltd. (UK),hessian jute fabrics (Natural Color Burlap, Material: 100% Jute,Width:47 00 ,11 Oz.),andMontmo-rilloniteK10nanoclay(surfacearea:220–270 m 2 /g)suppliedbySig-ma–Aldrich (USA) were used as matrix, reinforcement, andnanofillers in this study. Alcojet detergent, 50% ethanol solution,50% NaOH solution,and 99%acetic acid solutionfor chemicaltreat-ments, and 99% chloroform solution to dissolve Biopol were used.These chemicals were also collected from Sigma–Aldrich (USA).  2.2. Surface modification Detergent washing, dewaxing, alkali treatment, and soakingwith acetic acid were performed on hydrophilic jute fibers to im-prove interfacial bonding with hydrophobic polymer, biopol. Dirtwas removed from fibers by detergent washing keeping fibers into5% detergent solutions at 30   C for 1 h and washing them subse-quently with water. After drying pectin was removed from thesedetergent washed fibers by keeping them into 5% ethanol solutionat 30   C for 1 h followed by washing with water and drying.Dewaxed fibers were kept into 5% NaOH solution at 30   C for 2 hand washed with distilled water to remove lignins and hemicellu-loses. Alkali treatment resulted in major number of   A OH groupaccessible on surfaces of fibers [16], and broke down fiber bundles into single fibers and increased effective surface area available forinteracting with matrix. Alkali treated fibers were soaked with dis-tilled water–acetic acid (2%) solution for 1 h, followed by washingwith distilled water and drying. Acetic acid neutralized sodiumions that came with fibers during alkali treatment, reacted with A OH group on fiber surfaces to convert hydrophilic surfaces of fi-bers into hydrophobic for better adhesion with biopol.  2.3. Composite fabrication  Jute biopol composites were fabricated using treated and un-treated fibers and biopol by compression molding process. Biopolwas dissolved into chloroform at a ratio of 1:8 at room tempera-ture and stirred by magnetic stirrer for 4 h to prepare a homoge-neous solution. In case of nanophased composites, nanoclay wereinfused into biopol using solution intercalation techniques [23].Measured amount of nanoclay was dissolved into chloroform andsolution was then poured to biopol chloroform solution and againstirred for 2 h to prepare a homogeneous mixture. Final solutionwith/without nanoclay was poured into a mold to prepare a1.5 mm thick film and dried in a vacuumoven at 60   C to evaporateall choloroform. Dried thick films were then placed in the hot pressand 13.34 kN force was applied at 166   C for 10 min to prepare0.50 mm thin films. Jute–biopol composites were manufacturedby stacking prepared films with/without nanoclay and treated/un-treated fibers like a sandwich using compression molding processapplying 13.34 kN force at 166   C for 15 min.  2.4. Experimental procedures The FTIR spectra of parent and surface treated jute fibers wererecorded using Nicolet 6700 DX IR spectrophotometer with atten-uated total reflectance (ATR) sampling. The crystal material for theATR was diamond. The background was taken after every 60 minand each spectrum was recorded by co-adding 32 scans at4 cm  1 resolution within the range 4000–600 cm  1 . Three samplesfrom each batch were tested for this test. FTIR spectra technique isused to find the functional groups present both above and just be-low the top molecular layer of flat surface [24].Tensile properties of untreated and treated jute fiber bundleswere characterized using Zwick Roell testing unit according toASTM D2256-02 standard under displacement control mode at astrain rate of 0.5 min and on a gauge length of 50 mm. The diame-ter of the round fiber bundle was measured with an optical micro-scope and ten samples from each category were tested.Morphological characterization of the treated and untreated fi-bers was conducted using a JEOL JSM-5800 scanning electronmicroscope (SEM). The fibers were coated with silver using sput-tering machine to prevent charging.Void content of the jute biopol composites was determinedaccording to ASTM D2734-94 standard [25] using the followingequations. V  v   ¼ ½ð q t    q Þ = q t    100  ð 1 Þ q t   ¼  1 = ½ W   f  = q  f   þ W  m = q m  þ W  n = q n  ð 2 Þ V   f   ¼ ð W   f  = q  f  Þ = ½ W   f  = q  f   þ W  m = q m  þ W  n = q n  ð 3 Þ 1702  M.K. Hossain et al./Composites: Part B 42 (2011) 1701–1707   q e  ¼  sample weight  ð gm Þ = sample volume  ð cm 3 Þ ð 4 Þ where,  V  v ,  V   f  ,  q t   and  q e  are the percentage void fraction, fiber vol-ume fraction (considering no void), theoretical density and experi-mental density of the composites, respectively.  W   f  ,  W  m , and  W  n are the weight fraction and  q  f  ,  q m , and  q n  are the density of thefiber, matrix, and nanoclay, respectively. Density of biopol, jutefiber, and nanoclay were taken as 1.25 gm/cm 3 [19] and 1.4 gm/cm 3 [17], and 2.35 gm/cm 3 , respectively. Experimental density of the composites was calculated using Eq. (4). In this case, three sam-ples from each category were chosen and measured the weight(gm) and volume (cm 3 ) to calculate the density. In case of void frac-tion calculation, average experimental density ( q e ) was used. Storage modulus (E 0 ), loss modulus (E 00 ), and tan delta (tan  d )(the ratio of E 00 and E 0 ) of jute–biopol samples were obtained fromthe DMA tests under three point bending mode at a heating rate of 5   C/min from 30 to 120   C with an oscillation frequency of 1 Hzand amplitude of 15 l m according to ASTM D4065-01 standard.Three samples from each category were tested.Moistureabsorptiontestsofuntreated/treatedjute–biopolcom-posites were conducted according to ASTM D2495-07. Five rectan-gular samples from each category (dimension: 100  13   3 mm)were dried in a vacuum oven at 105   C for 5 h and dry weight ( W  0 )was taken after cooling. To make a humid environment, some dis-tilled water was placed into a desiccator and after 12 h the insidehumiditywasfoundtobe98%.Drysampleswerethenkeptonaplat-formabovewaterinthedesiccator.Theweights( W  t  )ofthesampleswere measured after 7, 14, 20, 30, and 60 days conditioning using aprecision balance having an accuracy of 0.0001 gm. Moisture con-tent was calculated using the following equation. M  t  ð % Þ ¼ ½ð W  t    W  0 Þ = W  0   100  ð 5 Þ Flexural properties of jute–biopol composites with/withoutnanoclay were evaluated using Zwick Roell testing unit accordingto ASTM D790-02 standard under displacement control mode ata crosshead speed of 2.0 mm/min [26]. Five samples from each cat- egory were tested to determine the average result. 3. Results and discussion  3.1. Surface modification characterization Fig. 1 illustrates the FTIR spectra of different modified jute fi-bers. A broad absorption band in the region of 3200–3600 cm  1 characteristic of hydrogen bonded O A H stretching vibration [27],was common to all of the spectra. The O A H stretching vibrationwas decreased due to the alkali treatment that resulted in moreO A H groups accessible on the fiber surface for the reaction withthe acetic acid. The C A H stretching vibration of methyl and meth-ylene groups in cellulose and hemicelluloses was observed near towave number 2950 cm  1 [28]. It was also decreased due to the sur-face modification. Hemicelluloses are the main concern of our sur-face modification, which appeared near to the 1730 cm  1 wavenumber for the C @ O stretching vibration of the carboxylic acidand ester components of hemicelluloses. Hemicelluloses were dis-solved into the alkali solution and no peaks was observed in the al-kali treated fibers for C @ O stretching vibration. The absorbanceband near to 1464 cm  1 wave number is responsible for lignin[11]. This peak was weakened due to the chemical treatment,which was the indication of removal of lignin from the treated fi-bers. As the exposure time of fibers into the sodium hydroxidesolution increases, the percentage of cellulose content increases.However, sodium hydroxide has a direct effect on the mechanicalproperties of the fibers. Fibers exposed into the 5% sodium hydrox-ide solution for 2 h and washed with the 2% acidic acid solution for1 h showed optimum results for the surface modification.Uniaxial tensile test results of treated and untreated jute fiberbindles are shown in Fig. 2 and Table 1. Fibers treated with NaOH for 2 h exhibited improvements in tensile strength and modulus by13% and 17%, respectively, compared to untreated fibers. Alkalitreatment caused removal of non-cellulosic materials, includinghemicellulose, lignin, and pectin from interfibriller regions [17]and resulted in a higher percentage of cellulose, which was themain contributor to the higher tensile strength and modulus of fibers [11]. Higher concentrations of NaOH or longer exposed to NaOH weaken fibers and make it more brittle. Two hour-exposuretimes with 5% NaOH showed optimum results.Surfaces of treated and untreated fibers investigated using SEMmicrographs (Fig. 3) revealed relatively rougher surfaces in treatedfibers compared to untreated fibers. Removal of surface impurities,non-cellulosic substances, inorganic materials, and waxes resultedin cleaner and rougher surfaces in finally treated fibers. Chemicaltreatments converted the mesh-like structure of fibers to cleanand rough single fibers which provided higher strength to fibers.This observation was reported elsewhere [29]. Rougher surface and defibrillation were also attributed to better interaction of fibers with matrix for larger surface area.  3.2. Composite characterization The presence of trapped air or volatile materials and incompletewetting out of the fibers by the matrix causes the void content into Fig. 1.  FTIR spectra of treated and untreated jute fibers. Fig. 2.  Tensile stress–strain curves of treated and untreated jute fibers. M.K. Hossain et al./Composites: Part B 42 (2011) 1701–1707   1703  the fiber reinforced composites [30,31]. Higher percentage of void was observed in the UTJBC compared to the TJBC (Table 2). Thiswas expected due to the lack of proper interaction between thehydrophilic untreated fibers and hydrophobic matrix. Nanoclayacts as a nucleating agent and takes the space into the voids.Hence, the lower void content was found in the nanoclay infusedsamples, compared to the conventional composites. As the per-centage of nanoclay increases, the percentage of void content de-creases into the samples. There are still some voids present inthe samples. When the fill and warp direction fiber cross eachother, it may cause the presence of voids into the composite sys-tem. The fiber volume fraction (considering no void present) calcu-lated using Eq. (3) was found to be about 0.27 for all kinds of composites.DMA was performed to study the response of stiffness of the jute/biopol composites as a function of temperature. From DMAtests(Fig.4a),itwasobservedthatstoragemoduluswasthehighestat room temperature and decreased linearly with increasing tem-perature. Storage modulus (1605 MPa) was higher in TJBC com-pared to UTJBC (1467 MPa). This may be attributed to the betterinterfacialbondingbetweenfiberandmatrixforthechemicaltreat-ment. Jute/Biopol samples with 2%, 3% and 4% nanoclay showedabout 2550, 2900, and 3050 MPa storage modulus at 30   C, respec-tively. Higher storage modulus with increasing nanoclay content isthe indication of the higher crystallinity and brittleness of thecomposites. A small bump in the region 50   C was observed in thesamples withoutnanoclay. It indicates the cold crystallization tem-perature region. During the heating cycle, the specimen enters into  Table 1 Tensile test results of treated and untreated jute fibers.  Jute fiber bundle Strength (MPa) Strength change (%) Strain at failure (%) Strain change (%) Modulus (GPa) Modulus change (%)Untreated 81.42 ± 10 0 3.83 ± 0.62 0 1.92 ± 0.45 01 h NaOH treated 85.04 ± 13 4.9 3.62 ± 0.67   5 2.06 ± 0.64 7.32 h NaOH treated 92.54 ± 11 13 3.21 ± 0.68   16 2.25 ± 0.26 173 h NaOH treated 91.68 ± 10 12 3.34 ± 0.64   13 2.26 ± 0.34 17.75 h NaOH treated 80 ± 13   1.2 2.98 ± 0.69   22 2.28 ± 0.74 18.7 Fig. 3.  SEM micrographs of different phase surface treated jute fibers.  Table 2 Fiber volume fraction and void content of jute biopol composites. Type of composites Weight fraction Fiber volume fraction ( V   f  ) Theoretical density( q t  ) (gm/cm 3 )Experimental density( q e ) (gm/cm 3 )Void content (%)Fiber ( W   f  ) Matrix ( W  m ) Nanoclay ( W  n )UTJBC 0.30 ± 0.05 0.69 ± 0.04 0 0.27 ± 0.02 1.29 1.150 ± 0.01 10.8TJBC 0.29 ± 0.02 070 ± 0.03 0 0.275 ± 0.01 1.291 1.182 ± 0.02 8.32% Nanoclay TJBC 0.29 ± 0.03 0.69 ± 0.03 0.014 0.273 ± 0.01 1.299 1.222 ± 0.07 5.93% Nanoclay TJBC 0.29 ± 0.03 0.68 ± 0.02 0.021 0.269 ± 0.01 1.30 1.230 ± 0.02 5.34% Nanoclay TJBC 0.28 ± 0.03 0.68 ± 0.02 0.028 0.268 ± 0.01 1.299 1.250 ± 0.02 3.81704  M.K. Hossain et al./Composites: Part B 42 (2011) 1701–1707   the cold crystallization region where crystallinity increases and therate of decrease of storage modulus (E 0 ) decreases [17]. Thus, a small bump was noticed in this region. Lower cold crystallizationtemperature(about40–45   C)wasfoundinthesampleswithnano-clay, due to the clay’s action as a nucleating agent in the polymericcomposites.Tangent delta (tan  d ) as a function of temperature is illustratedin Fig. 4b. It provides the account of energy dissipated as heat dur-ing the dynamic testing [32]. As the stiffness increases, the tan  d value decreases reflecting reduced energy losses. With increaseof temperature, energy losses increase; thus the value of tan  d  in-creases. Nanoclay infusion into the biocomposites decreased thetan  d  value indicating a higher degree of crystallinity. Crystallinestructure reduces the loss modulus giving rise to the storage mod-ulus. Loss modulus is related to the molecular chain movement of the polymer. Lower loss modulus was observed in nanoclay in-fused samples, due to nanoclay’s imposed restriction to the expan-sion of the molecular chain in the amorphous region.Table 3 shows the percentage of moisture absorbed by the jutebiopol composites at different time period. Most of the natural fi-bers have a tendency to absorb moisture when they are placed ina humid area which weakens the composites. The percentagemoisture absorption for conventional and nanophased compositeswas almost the same during initial 7 day conditioning period. Asthe conditioning time was increased, the amount of absorbedmoisture was increased. After 20 days, it became almost saturatedand there was no significant change in the moisture absorptiondata even after conditioning for 30 and 60 days. The amount of moisture absorbed by the UTJBC was higher compared to the TJBCand nanoclay infused TJBC, due to the presence of micro voids inthe UTJBC for improper interaction between fiber and matrix.Nanoclay infused samples showed lower percentage of moistureabsorption, because nanoparticles acted as a moisture barrier tothe composites system.The flexural results of untreated and treated jute–biopol com-posites are shown in Fig. 5a. Surface modified fibers resulted inbetter adhesion with the matrix. As a result, better flexural proper-ties were found in TJBC compared to UTJBC without nanoclay. Nan-ophased TJBC had resulted in higher strength and modulus.However, addition of nanoclay was attributed to brittleness incomposites, which was obvious from reduced percentage of strainat maximum stress. No fiber failure was observed in the both nan-ophased and conventional green composites. Only the matrix fail-ure occurred. It was also noticed that the jute based compositesshowed the higher flexural strain, which is the indication of theductile nature of the jute based biocomposites.Flexural properties of these composites were also determinedafter moisture absorption for 60 days (Fig. 5b). Higher flexuralstrength and flexural modulus were observed in TJBC comparedto UTJBC. Better flexural properties were also observed in nanoclayinfused samples compared to conventional composites. However,the flexural strength and modulus were decreased after moistureabsorption, as expected. The results are shown in Table 4. The per-centage decrease in the flexural strength was highest (32%) in theUTJBC and lowest (15%) in the 4 wt.% nanoclay infused samples.The respective values for flexural modulus were 21% and only6–7% respectively. It is also the indication of the moisture barrierproperties of the nanoclay into the composites system. 4. Conclusion Surface treatments resulted in the removal of pectin, hemicellu-loses, and other non-cellulosic substances from the fibers and thehigher percentage of celluloses in the final treated fibers. Roughersurface and increased effective surface area of the chemically trea-ted fibers facilitated better interaction between the fiber and ma-trix. Surface modified fibers showed better tensile propertiescompared to untreated fibers for the presence of higher percentageof crystalline celluloses.Natural fibers possess very good specific properties, which arecomparable to synthetic fibers. By increasing the fiber volume 50010001500200025003000350030405060708090100110120 4% Nanoclay TJBC3% Nanoclay TJBC2% Nanoclay TJBCTJBCUTJBC    S   t  o  r  a  g  e   M  o   d  u   l  u  s   (   M   P  a   ) Storage Modulus VS Temperature Curves of Jute Biopol Composites 4% Nanoclay TJBC3% Nanoclay TJBC2% Nanoclay TJBCFTJBCUTJBC Temperature ( ° C)    T  a  n         δ Tan Delta VS Temperature Curves of  Jute Biopol CompositesTemperature ( ° C) (a) (b) Fig. 4.  DMA curves (a) storage modulus, and (b) Tan  d .  Table 3 Moisture absorbed by jute biopol composites. Moisture gain (%) After 7 days After 14 days After 20 days After 30 days After 60 daysUTJBC 3.987 ± 0.23 5.816 ± 0.16 6.148 ± 0.34 6.189 ± 0.18 6.279 ± 0.13TJBC 3.836 ± 0.62 5.026 ± 0.53 5.835 ± 0.27 5.949 ± 0.44 5.938 ± 0.402% Nanoclay TJBC 3.651 ± 0.44 4.572 ± 0.30 5.669 ± 0.29 5.824 ± 0.29 5.882 ± 0.253% Nanoclay TJBC 3.639 ± 0.35 4.554 ± 0.36 5.475 ± 0.47 5.744 ± 0.37 5.8023 ± 0.104% Nanoclay TJBC 3.602 ± 0.24 4.5792 ± 0.17 5.337 ± 0.35 5.643 ± 0.26 5.775 ± 0.21 M.K. Hossain et al./Composites: Part B 42 (2011) 1701–1707   1705
Similar documents
View more...
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks

We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

More details...

Sign Now!

We are very appreciated for your Prompt Action!