Numerical Simulations of Shell-Side Two-Phase Flow in Spiral-Wound Heat Exchanger

Numerical Simulations of Shell-Side Two-Phase Flow in Spiral-Wound Heat Exchanger for Natural Gas Liquefaction Dan-Hermann S Thue Master of Science in Mechanical Engineering Submission date: December 2015
of 86
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Numerical Simulations of Shell-Side Two-Phase Flow in Spiral-Wound Heat Exchanger for Natural Gas Liquefaction Dan-Hermann S Thue Master of Science in Mechanical Engineering Submission date: December 2015 Supervisor: Trygve Magne Eikevik, EPT Norwegian University of Science and Technology Department of Energy and Process Engineering Science and Technology Department of Energy and Process Engineering EPT-P MASTER THESIS for Dan-Hermann Schmeling Thue Autumn 2015 Numerical simulations of shell-side two-phase flow in spiral wound heat exchanger for natural gas liquefaction Strømningssimuleringer av skall-siden i en Spiral-tvunnet varmeveksler for produksjon av flytende naturgass Background and objective When remote and small scale gas fields are to be exploited, liquefied natural gas (LNG) is a major solution to the problem of transportation, as opposed to using pipelines. LNG also has a transportation cost advantage over long distances compared to pipelines. The global demand for LNG is expected to rise in the following years, especially in Asia, which increases the importance of researching the liquefaction process. One of the most critical components of the process is the spiral wound heat exchanger (SWHE). However, little research about the design basis of the SWHE is openly available as there are few manufacturers. Especially on the shellside. The objective of this thesis is concentrated on making use of a simulation model approach of the falling film flow on the shell-side of the heat exchanger using ANSYS software. In the twophase flow, the mass flow rate, the different velocities of liquid and gas and the vapor fraction can be measured to see how it influences the flow pattern. I The following tasks are to be considered: 1. Literature study of spiral wound heat exchangers and the cryogenic liquefaction section of liquefying natural gas using a mixed refrigerant 2. Create and simulate a simplified 3D model of the SWHE 3. Test the 3D model under different vapor fractions and flow rates and then check influence on flow patterns 4. Compare results of measured void fractions with the best prediction model available 5. Compare flow pattern results with the lab experiment 6. Proposal of further work The project work comprises 15 ECTS credits. The work shall be edited as a scientific report, including a table of contents, a summary in Norwegian, conclusion, an index of literature etc. When writing the report, the candidate must emphasize a clearly arranged and well-written text. To facilitate the reading of the report, it is important that references for corresponding text, tables and figures are clearly stated both places. By the evaluation of the work the following will be greatly emphasized: The results should be thoroughly treated, presented in clearly arranged tables and/or graphics and discussed in detail. The candidate is responsible for keeping contact with the subject teacher and teaching supervisors. Risk assessment of the candidate's work shall be carried out according to the department's procedures. The risk assessment must be documented and included as part of the final report. Events related to the candidate's work adversely affecting the health, safety or security, must be documented and included as part of the final report. If the documentation on risk assessment represents a large number of pages, the full version is to be submitted electronically to the supervisor and an excerpt is included in the report. According to Utfyllende regler til studieforskriften for teknologistudiet/sivilingeniørstudiet ved NTNU 20, the Department of Energy and Process Engineering reserves all rights to use the results and data for lectures, research and future publications. The report shall be submitted to the department in 3 complete, bound copies. An executive summary of the thesis including title, student s name, supervisor's name, year, department name, and NTNU's logo and name, shall be submitted to the department as a separate pdf file. The final report in Word and PDF format, scientific paper and all other II material and documents should be given to the academic supervisor in digital format on a DVD/CD-rom or a memory stick at the time of delivery of the project report. Submission deadline: January 19, Work to be done in lab (Water power lab, Fluids engineering lab, Thermal engineering lab) Field work Department for Energy and Process Engineering, 22 August Prof. Olav Bolland Department Head Prof Trygve M. Eikevik Academic Supervisor Research Advisor(s): Prof. G.L. Ding (SJTU) Prof Trygve M. Eikevik (NTNU) s N.N III Preface The program is a joint-research venture collaboration between The Norwegian University of Science and Technology (NTNU) and Shanghai Jiao Tong University (SJTU). This thesis was written at SJTU and results in a degree from both universities. The dissertation topic is issued by Institute of Refrigeration and Cryogenics and the period of the project spans from September 2014 to December Professor 丁国良 (Ding GuoLiang) is the academic supervisor from SJTU and Professor Trygve Magne Eikevik is the supervisor from NTNU. Lab experiments were sponsored by Chinese National Offshore Oil Corporation (CNOOC). I also want to thank DingChao and LiJanRui for the theoretical discussions and support in the matters Chinese. Dan-Hermann Thue Shanghai, Dec I Abstract Heat transfer coefficients and pressure drop of evaporating heat exchangers such as the spiral wound heat exchanger depend on the distribution of the refrigerant fluid. However little open research is available in the study of Spiral wound heat exchangers (SWHE) flow for LNG liquefaction. Only a handful of producers have the most experience in the production of such heat exchangers. The number of studies on two-phase liquid-gas flows on shell side of heat exchangers are still limited compared to in tube two phase flows. Most studies already done have focused on air water mixtures and some CFC refrigerants, which are now banned in most countries. In addition, the most commonly covered mass flows are in a larger range than typically used in refrigeration systems, in which typical systems use a range of 5 to 60 kg/m 2 s. A method of flow patterns study of two phase liquid-gas flow over a horizontal tube bundle has been developed. The tube bundle is comparable, although simplified, to the geometry in the spiral wound heat exchanger tested in the laboratory at Shanghai Jiao Tong University. Liquidvapor two-phase shell side flow phenomena is simulated in 3D using ANSYS ICEM for meshing, Fluent for calculations and CFD-Post data accumulation software. Flow patterns and data are observed mainly at vapor qualities between 0.1 and 0.7 and mass flux range of kg/m 2 s. A method for measuring void fractions is established and then compared according to established theory. The Feenstra-Weaver-Judd method is so far the most advanced prediction model and the best fitting for the largest part of the range studied. The higher the mass flux and vapor quality the better the prediction is comparted to the model. A close relationship between void fraction, and transition to new flow patterns was discovered. Especially in differences between spray flow and falling film flow. The measured void fractions were found to vary when increasing the vertical distance of the tubes. When increasing from 1mm to 4mm at a constant mass flux, the void fractions were consistently higher and the transition to a new flow regime thus came faster and at a lower vapor quality. The model is compared against the findings of the laboratory test at SJTU with propane, and the correlation of flow patterns fit well with the simulations. The CFD models flow pattern results were compared to results from lab experiments. The geometry in the CFD model is simplified compared to the SWHE model in the lab. Despite this there was good agreement with the flow pattern findings between simulation and lab results. Different fluids and geometries can be tested using this model. In this report, Propane was used as refrigerant fluid and material properties were obtained using REFPROP software at saturation point for 0.3 MPa. II Sammendrag Studien av 2-fase strømningsmønstre i skall siden av spiral-tvunnede varmevekslere har stor betydning for virkningsgraden, varmeoverføringen og trykktapet. Lite åpen forskning er tilgjengelig på området ettersom det er få aktører på markedet som produserer slike varmevekslere. Antallet to-fase studier gjort på skall siden av varmevekslere er svært få til sammenlikning med studier på strømning i rør. I tillegg er de fleste eksisterende studier fokusert på vann-luft blandinger og har ofte massestrømmer utenfor det området som er aktuelt for SWHE for LNG produksjon, nemlig mellom 5 60 kg/m 2.s. Det ble utviklet en metode for å studere vertikal strømningsmodus til to-fase strømning med Propan over en horisontal rørbunt, som ofte er å finne i varmevekslere. Geometrien til denne rørbunten er liknende geometrien til en modell av en SWHE som testes i laboratoriet ved Shanghai Jiao Tong Universitetet under liknende tilstander. En sammenlikning ble ført mellom lab-testene og simuleringene. Det ble funnet god overensstemmelse hva gjelder strømningskart og strømingsmoduser ved de aktuelle massefluksene og gasskvalitetene. Simuleringsmetoden ble utviklet som en del av oppgaven og under veiledning fra SJTU. ANSYS programvare ble benyttet, ICEM for å lage mesh, Fluent for å bergene og CFD Post for å behandle data. Simuleringen er gjort i 3D ved bestemte verdier for gasskvalitet og massestrøm. Massestrømmen varierte mellom kg/m 2.s og gass kvaliteten mellom 0.1 og 0.7. Propan ved 3 bar fordampningstemperatur er benyttet og termodynamiske data hentet fra REFPROP programvare. Data lest fra målingene var gass-volumfraksjonen og arealfraksjonen i bestemte utsnitt i 3D modellen, samt individuelle gass og væske hastigheter ved nevnte utsnitt. Dette ble brukt til sammenlikning med teoretiske prediksjonsmetoder utarbeidet av tidligere forskere. Feenstra- Weaver-Judd modellen viste seg å være den mest nøyaktige prediksjonsmodellen, men hadde problemer ved samtidig lave massestrømmer og gasskvaliteter. Nøyaktigheten økte ved økning av disse parameterne. Gassvolumfraksjonen økte når den vertikale distansen mellom rørene ble økt. Tester mellom 1mm, 2mm og 4mm vertikal distanse ble simulert. Simuleringsmodellens strømningsmønstre ble sammenliknet med strømningsmønstrene observert ved lab forsøk ved SJTU. Det ble funnet god overensstemmelse med resultatene for disse. Propan ble brukt ved simulering og lab sammenlikning. Simuleringsmodellen er en forenklet modell av lab modellen. Denne simuleringsmetoden kan dermed være svært nyttig for å simulere forskjellige to-fase blandinger på skall siden over rør bunter og kan testes for forskjellige geometrier hurtig og effektivt sammen. III Table of Contents Preface... I Abstract... II Sammendrag... III 1. Background and Motivation... 2 Liquid Natural Gas (LNG)... 2 LNG status LNG Prospects Spiral wound heat exchanger (SWHE)... 6 Dimensions of SWHE... 8 LNG liquefaction cycles APCI propane precooled mixed refrigerant process Philips optimized cascade LNG process PRICO process Statoil/Linde mixed fluid cascade process Literature Review: State of the Art Flowrate, Film flowrate and Reynolds number Falling film flow over open horizontal tubes Capillary influence and surface tension Falling flow over Horizontal tube bundles Flow Pattern estimations Void fractions Horizontal tube CFD simulations Falling flow in SWHE Flow patterns influence on heat transfer Factors influencing the heat transfer coefficient IV 3. CFD model setup CFD Governing Equations Continuity equations Momentum equation Surface tension Material properties Energy Equation D and 3D models Geometry Meshing Fluent solver solution setup Solution Models Multiphase flow simulation: The volume of fluid model (VOF) Viscous and turbulence model: Shear stress transport (SST) k- ω Energy equation Materials and phases Materials Phases Boundary conditions Inlet Outlet Tube walls Left and right sides Front and back sides Solution Methods: Calculation Activities Methodology V Determining the inlet void fraction Determining Inlet vapor and liquid velocities Variables Test for Mesh independent solution Operating conditions Quality Quality Coarse mesh: Verifying Mass flow integrity of simulations Extracting measurements on the simulation models Results and Discussion Flow patterns Capillary length influence: Droplet flow with water-air Simulation Slip ratio results Void fraction results Shear flow results 0.9 ɛ Intermittent flow/transition flow regimes 0.75 ɛ Falling film flow regime ɛ Comparison with Void fraction prediction models Results from 4mm tube gap Comparison with results from laboratory experiment Sources of error CFD Model Conclusions Recommendations for future work References VI Table of Figures FIGURE 1-1 NATURAL GAS MAJOR TRADE MOVEMENTS 2012 (CHEN, 2014)...3 FIGURE 1-2 TRADE BALANCE IN GLOBAL MARKETS OF LNG IN MEGATONNES BETWEEN 2013 AND (BG- GROUP, 2014)...4 FIGURE 1-3- PRICE DEVELOPMENT AND PREDICTIONS OF MAJOR LNG REGIONAL MARKETS.(BG-GROUP, 2014).5 FIGURE 1-4 PRODUCTION STEPS OF CWHE...7 FIGURE 1-5 MUTISTREAM SWHE...8 FIGURE 1-6 CROSS SECTION ILLUSTRATING THE INNARDS OF AN SWHE...8 FIGURE 2-1 SIMPLIFIED MODEL OF FALLING FILM FLOW (FERNÁNDEZ-SEARA AND PARDIÑAS, 2014) (HALF TUBE)...11 FIGURE 2-2 MITROVIC, J. INFLUENCE OF TUBE SPACING AND FLOW RATE ON HEAT TRANSFER FROM A HORIZONTAL TUBE TO A FALLING LIQUID FILM. (MITROVIC, 1986)...12 FIGURE FLOW MODE TRANSITIONS WHEN NEGLECTING HYSTERESIS (HU AND JACOBI, 1996)...13 FIGURE 2-4 FLOW REGIME MAP DEVELOPED BY (NOGHREHKAR ET AL., 1999) FOR A) IN-LINE TUBE ARRANGEMENT AND B) STAGGERED. VERTICAL UPWARD FLOW ACROSS TUBE BUNDLES WITH AN AIR- WATER TWO PHASE FLOW FIGURE FLOW PATTERNS IN VERTICAL DOWN-FLOW ACROSS A HORIZONTAL TUBE BUNDLE: (A) FALLING FILM FLOW; (B) INTERMITTENT FLOW; (C) ANNULAR FLOW; (D) BUBBLY FLOW (XU ET AL., 1998)...16 FIGURE 2-6 COMPARISON OF DIFFERENT VOID FRACTION PREDICION MODELS IN HORIZONTAL FLOW SHELL SIDE TUBE BUNDLE FLOW, BY (JOHN R. THOME, 2010)...19 FIGURE 2-7 EXPERIMENTAL RESULTS FROM (XU ET AL., 1998) DOWNWARD FLOW WITH AIR-WATER. IN LINE SQUARE ARRANGEMENT WITH A PITCH TO DIAMETER RATIO OF 1.28 VOID FRACTION MEASURED IS VOLUMETRIC FIGURE TUBE HORIZONTAL TUBES MODEL WITH DOWNWARD FLUID FLOW, CUT ALONG THE MIDDLE AND MIRRORED ALONG THE VERTICAL AXIS FIGURE 2-9 WU ET AL. MODEL OF SWHE...22 FIGURE 2-10 FLOW MAP OF FALLING FILM FLOW: (FF) FILM FLOW; (IN) INTERMITTENT (XU ET AL., 1998)...23 FIGURE 3-1- INVENTOR SKETCHES (X-Y-PLANE) OF THE 1MM AND 4 MM VERTICAL TUBE SPACING MODEL GEOMETRIES. FOR 3D MODELLING AN EXTRUSION OF 10MM DEPTH IS USED IN BOTH CASES FIGURE 3-2- ILLUSTRATION OF WHAT THE TUBE BUNDLES LOOK LIKE WITH ALL DIMENSIONS FROM TABLE 1 INCLUDED FIGURE FIGURE 3-4 MESH OF TUBE BUNDLE MODEL WITH 3 TUBES. LEFT: 1MM VERTICAL TUBE GAP (P/D=1.08). RIGHT: 4MM VERTICAL TUBE GAP (P/D) FIGURE 3-5 OVERVIEW OF THE SOFTWARE USED IN ANSYS WORKBENCH, FROM LEFT ICEM CFD, FLUENT AND CFD POST VII FIGURE VOF MODELLING OF A FLUID-FLUID SURFACE (A) REPRESENTS THE REAL SURFACE, (B) THE VOLUME FRACTION CALCULATED BY THE VOF MODEL AND (C) IS THE VOF MODELS LINEAR RECONSTRUCTION OF THE SURFACE...33 FIGURE 3-7 BOUNDARY LAYER IN THE MIDDLE AND TUBE INTERIOR AT LEFT. EXTRA FINE MESH DENSITY. RED LAYER IS LIQUID. BOUNDARY LAYER THICKNESS MODELED AT 0.2MM...34 FIGURE 3-8 SOLUTION METHODS USED FOR SIMULATIONS...37 FIGURE COMPARISON OF MESH SOLUTIONS FOR VAPOR QUALITY X=0.1. FROM TOP: COARSE MESH, MEDIUM MESH AND FINE MESH. AT THE RIGHT SIDE, A ZOOMED PERSPECTIVE OF THE OUTLET IS SHOWN FIGURE 4-2 A) COARSE MESH AT 0.4 SECONDS B) MEDIUM MESH AT 0.4S...42 FIGURE 4-3 FINE MESH SOLUTION AT SEEN FROM FRONT AT TIME 0.4 SECONDS (LEFT), AND SEEN FROM THE BACK SIDE AT 0.6 SECONDS WHEN ONE SIDE HAS BECOME ALMOST SYMMETRICAL IN THE X-Y PLANE(RIGHT)...43 FIGURE EXTRA FINE MESH AT 0.4S TWIST PHENOMENA OCCURRING...43 FIGURE 4-5 MEASUREMENT LOCATIONS OF VAPOR AND LIQUID VELOCITIES AND AREA FRACTIONS USED TO CALCULATE SUPERFICIAL VELOCITIES. BLACK CUT PLANE AND PURPLE CUT PLANE WAS USED AND AVERAGED. QUALITY X0.1 AND FLOWRATE G30 USED AS EXAMPLE HERE FIGURE 5-1 FLOW MAP INDICATING FLOW MODE TRANSITIONS BASED ON VAPOR QUALITY AND MASS FLUX OVER THE IN LINE TUBE BUNDLE WITH 1MM VERTICAL TUBE SPACING FIGURE 5-2 WATER AIR SIMULATION DO INDUCE DROPLET FLOW. X= AND G=0.75 KG/M 2 S. RE L = FIGURE 5-3: ATTEMPT TO HAVE WETTED TUBE WALLS AND DROPLET FLOW. X= AND G=1.75. RE L = FIGURE 5-4 SLIP FACTORS S FOR ALL 1MM VERTICAL TUBE GAP SIMULATIONS ARRANGED AFTER MEASURED VOLUMETRIC VOID FRACTIONS FIGURE 5-5 VOLUMETRIC VOID FRACTION MEASUREMENTS FOR 1MM VERTICAL TUBE SPACING CASE...53 FIGURE 5-6 FILM THICKNESS MEASURED AT THE LOWEST TUBE AT THE THINNEST CROSS SECTIONAL AREA AND WHERE THE VELOCITY AND THUS FILM THICKNESS WERE USUALLY THINNEST. MEASUREMENTS FOR 1MM VERTICAL TUBE SPACING CASE...54 FIGURE 5-7 SHEAR FLOW CASE EXAMPLE. SIMULATION VAPOR QUALITY X = 0.7 AND MASS FLOWRATE G = 40 KG/M 2 S...55 FIGURE 5-8 QUALITY 0.7 MASS FLUX 20 KG/M 2 S LIQUID FILM THICKNESS IS VERY LOW ON THE SIDES BUT LIQUID AGGREGATES BETWEEN THE TUBES IN A LARGER DEGREE. OCCASIONAL DRY SPOTS ON THE LOWER TUBE FIGURE 5-9 A) AND B) FALLING FILM FLOW REGIME G 30 KG/M 2 S AND QUALITY X = 0.1. C) COMPARED TO INTERMITTENT FLOW REGIME WITH HIGH GAS VELOCITIES REPRESENTED BY G 20 KG/M 2 S X = FIGURE 5-10 FALLING FILM FLOW. G50 AND X0.1 TOP FRONT AND SIDE VIEW AT T=0.66S...58 FIGURE COMPARISONS OF VOID FRACTION PREDICTION METHODS FOR 1MM TUBE GAP CASE, BLACK LINES AND POINTS ARE RESULTS OBTAINED FROM SIMULATIONS COLORED ARE ESTIMATIONS:...59 VIII FIGURE 5-13 COMPARISON OF VOID FRACTION PREDICTION METHODS FOR 4MM TUBE GAP CASE...63 FIGURE 5-14 A COMPARISON OF THE FLOW MODES OBSERVED AT SPECIFIC VAPOR QUALITIES AND MASS FLUXES. THE 1MM VERTICAL TUBE GAP SIMULATIONS FIT WELL WITH THE 2MM LAB EXPERIMENT OBSERVATIONS FIGURE 5-15 LEFT: FALLING FILM FLOW AND RIGHT: INTERMITTENT FLOW. PROPANE AT 4.5 BAR FROM OBSERVATIONS AT THE LAB SET UP IN SJTU TABLES TABLE 2-1. OVERVIEW OF PARAMETERS INFLUENCING THE HEAT TRANSFER COEFFICIENT, TABLE AND CONTENT CREDIT TO MASTER THESIS OF (JOHN G. BUSTAMENTE, 2014)...26 TABLE 3-1 MODEL GEOMETRIES...28 TABLE 3-2 SATURATION POINTS AT EQUILIBRIUM FOR PROPANE FROM 0.1MPA TO 1MPA, GENERATED USING REFPROP COMPUTER SOFTWARE.- NIST REFERENCE FLUID PROPERTIES...35 TABLE 5-1 RESULTS AND PREDICTIONS OF VELOCITY RATIOS/SLIP RATIOS IN THE SIMULATED RANGE. FLOW MODES MARKED WITH DIFFERENT COLORS: GREEN FIELDS ARE FF, ORANGE FIELDS ARE TRANSITION AREA (IN), AND RED IS SPRAY FLOW (SH)...51 TABLE 5-2 VOID FRACTION MEASUREMENT RESULTS...52 TABLE 5-3 PERCENTAGE DIFFERENCE BETWEEN MEASURED VOLUMETRIC VOID FRACTIONS AND THE FEENSTRA-WEAVER-JUDD PREDICTION MODEL NOMENCLATURE A Total cross sectional area, [m 2 ] α l Volume fraction liquid phase, dimensionless α v Volume fraction vapor phase, dimensionless D Tube Diameter, [m] E Energy, [ J ] ɛ Void fraction, dimensionless, [ Vol gas total vol ] F r Froude number dimensionless G Mass flux, [ kg sm 2 ] k eff Effective thermal conductivity [ W m. K ] IX m Mass flow rate [ kg s] P Pitch of tubes (vertical distance between tube centers) [m] p Pressure, [ N m 2 ] ρ Density, [ kg m 3 ] ρ v Density vapor phase, [ kg m 3 ] ρ l Density liquid phase, [ kg m 3 ] Q Volumetric flowrate, [ m3 s] Ri Richardson number, dimensionless S Slip factor, dimensionless, [ U GS ULS ] S h Source term (containing radiation) T Temperature, [K] u Velocity, [ m s] U vs Superficial velocity gas, (U vs = u v ɛ) [ m s] U ls Superficial liquid velocity, (U ls = u l (1 ɛ)[ m s] X Vapor fraction / Vapor quality, dimensionless ABBREVIATIONS AND SUBSCRIPTS CNG - Compressed Natural Gas FLNG - Floating liquefied natural gas fac
Related Search
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks

We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

More details...

Sign Now!

We are very appreciated for your Prompt Action!