Description

JOURNAL OF GEOPHYSICAL RESEARCH, VOL. 108, NO. C3, 3075, doi: /2001jc000820, 2003 A description of tides near the Chesapeake Bay entrance using in situ data with an adjoint model Z. R. Hallock, P.

Categories

Published

All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.

Similar Documents

Share

Transcript

JOURNAL OF GEOPHYSICAL RESEARCH, VOL. 108, NO. C3, 3075, doi: /2001jc000820, 2003 A description of tides near the Chesapeake Bay entrance using in situ data with an adjoint model Z. R. Hallock, P. Pistek, J. W. Book, and J. L. Miller Naval Research Laboratory, Stennis Space Center, Mississippi, USA L. K. Shay Rosenstiel School of Marine and Atmospheric Science, Miami, Florida, USA H. T. Perkins Naval Research Laboratory, Stennis Space Center, Mississippi, USA Received 30 January 2001; revised 16 September 2002; accepted 31 October 2002; published 13 March [1] Time series of surface elevation and current velocity in the vicinity of the Chesapeake Bay entrance are assimilated into a linear, barotropic model using an iterative adjoint method. Tide surface elevations, NOAA-NOS tidal data, moored acoustic Doppler current profiler (ADCP), and ocean surface current radar (OSCR) data are included in the assimilation. Data are analyzed for three tidal constituents (M 2, S 2, O 1 ); tidal series are constructed from these constituents and then used in the model assimilations. Statistics of predicted currents compare favorably with those calculated from data not used in the assimilation. An error analysis of the data distribution is performed for the M 2 tidal component, showing lower errors near assimilation data series but large errors, particularly for velocity, at some locations. Addition of a hypothetical current mooring dramatically reduces errors over most of the domain. We believe these results give the most demonstrably accurate description now available of tidal currents for this region of strong currents and heavy shipping. INDEX TERMS: 4219 Oceanography: General: Continental shelf processes; 4560 Oceanography: Physical: Surface waves and tides (1255); 4263 Oceanography: General: Ocean prediction; 4255 Oceanography: General: Numerical modeling; KEYWORDS: tides, data assimilation, Chesapeake Bay Citation: Hallock, Z. R., P. Pistek, J. W. Book, J. L. Miller, L. K. Shay, and H. T. Perkins, A description of tides near the Chesapeake Bay entrance using in situ data with an adjoint model, J. Geophys. Res., 108(C3), 3075, doi: /2001jc000820, Introduction [2] The objective of the present study is to use a dataassimilative numerical model to describe barotropic tidal variability in the vicinity of the entrance to the Chesapeake Bay (CBE) in the region shown in Figure 1. The large area of the Chesapeake Bay and its narrow, shallow entrance give rise to strong tidal currents, making the entrance of hydrodynamic interest. It is also, of course, a region of heavy shipping, both commercial and naval. In this and similar regions the barotropic tide is an ever-present phenomenon, affecting other coastal and estuarine processes (such as coastal fronts and river plumes), as well as human activities (e.g., shipping). The method described here allows the prediction of barotropic tidal elevations and currents to accuracies of a few centimeters and centimeters per second, respectively. Our approach is to use an adjoint technique of data assimilation (described in section 3). Data assimilation techniques have been used for decades in meteorology and, more recently, in oceanography. A comprehensive review is Copyright 2003 by the American Geophysical Union /03/2001JC000820$09.00 provided by Ghil and Malanotte-Rizzoli [1991]. A variant of this technique has been developed by Thacker and Long [1988] and subsequently advanced by Griffin and Thompson [1996] by applying it to observations on the shelf east of Nova Scotia. We have successfully applied a similar technique to data collected in various areas: on the California coast, in the Yellow sea, and in the Korea-Tsushima Strait [Pistek et al., 1997; Perkins and Pistek, 1998; Book et al., 2001]. With this approach, a solution to the linear, shallow water equations is found that best agrees with in situ measurements over a limited spatial and temporal domain. To find a solution that agrees with available measurements, a related system of equations, the adjoint of the original equations, is used to iteratively calculate the gradient of model prediction-data mismatch conditions with respect to the boundary conditions. This gradient estimate is iteratively used to adjust the boundary conditions until an optimum fit over the entire space-time domain is achieved. Hence boundary conditions are derived along with the solution, using in situ data within the domain of the model. [3] Currents in the region immediately outside the CBE are dominated by tides, density-driven flows, and wind forcing. Barotropic variability is due primarily to the M 20-2 HALLOCK ET AL.: TIDES NEAR THE CHESAPEAKE BAY ENTRANCE when assimilated into the model, yields an accurate description of the tides. That is, where independent (not assimilated) time series exist, statistics of model velocities compare favorably with those based on observations. However, an error analysis shows that a broader data distribution is needed to establish demonstrably correct fields in some parts of the model domain. The approach used here does not require a priori initial and boundary values. It is an efficient method which can describe the barotropic tidal environment in the vicinity of and just outside the CBE and to provide such a description with an assessment of its validity. [5] The following section describes the observations, consisting of elevation and current time series, that are assimilated into the model to provide a short-term prediction, as well as independent data sets used for comparisons with model results. Section 3 describes the adjoint model formulation. In section 4 we discuss results of the model calculations, compare statistics with those based on historical data sets, and assess the uniqueness/reliability of the solution for the M 2 constituent. Figure 1. Map of the COPE-1 area showing locations of data sets used in the assimilations. Elevation series, h 1, h 2, (triangles), ADCP (diamond), and OSCR gridpoints (circles). A hypothetical mooring location (square) is used in the error analysis. tide [Shay et al., 2001; Clarke, 1991], while the Chesapeake outflow plume, modulated by wind forcing, constitutes most of the baroclinic flow. Farther offshore ( 40 km), tidal currents become less important and the flow is increasingly dominated by slope currents and shelf waves [Biscaye et al., 1994]. Shay et al. [2001] report on the strength of the M 2 tidal current constituent from the immediate CBE area to about 25 km south of Cape Henry, based on ocean surface current radar (OSCR) and moored acoustic Doppler current profiler (ADCP) records (these same records are utilized in the present study but are assimilated into the adjoint model). Their results show dominance of the M 2 tide at the CBE (about 60% of the signal) with decreasing amplitudes southward. Biscaye et al. [1994], who describe observations just northeast of the region shown in Figure 1, find that subtidal fluctuations are aligned generally alongshore but that except very close to the coast, tidal currents are polarized across isobaths (70% 90% of variance). phase change in surface height for the dominant M 2 tide along the eastern seaboard is quite small, generally less than an hour between New York and the CBE (see, for example, Doodson [1958]). [4] In this work we assimilate time series of vertically averaged, in situ tidal current velocity, surface elevation, and surface current velocities obtained from remotely sensed OSCR measurements. To estimate the effectiveness of the available data in describing the M 2 constituent over the model domain, an error map is developed based on the data distributions in space and time. We find that this sparse collection of current velocity and surface elevation data, 2. Observations 2.1. Data Used in the Assimilations [6] Concurrent observations of time series of current velocity and surface elevation were used as input to the adjoint model assimilation. Observation locations are shown in Figure 1. [7] During the first Chesapeake Outflow Plume Experiment (COPE-1; September 1996), two upward looking acoustic Doppler current profilers (ADCPs) were deployed within 1 km of each other near N, W from 9 to 27 September 1996, in water depths of about 17 m. The data records from these instruments are virtually the same for the purposes of this study, so only one is used. Current velocity samples were acquired in 1 m vertical bins and 1 min ensemble averages of 60 pings each, giving an uncertainty in speed of about 1.5 cm s 1. The data were temporally smoothed to remove energy at periods shorter than 40 minutes and subsampled at 20 min to be compatible with other data sets. The location of this instrument is denoted by the diamond in Figure 1. [8] Surface elevation data from two locations (triangles, Figure 1) during COPE-1 are used. These include a NOAA- NOS prediction, based on harmonic analysis of historical data, for a location near Cape Henry (site 1) and a nearshore tide (pressure) gauge south of Cape Henry deployed as part of COPE-1 (site 2) (D. Johnson personal communication, 2001). [9] An ocean surface current radar (OSCR) system in its HF mode (25.4 MHz) was deployed from 15 September to 6 October 1996 to include the intensive observation period of COPE-1. Details of the OSCR land-based radar installations as well as preliminary data processing are described by Shay et al. [2001] and Haus et al. [1998]. Briefly, the OSCR system provides a two-dimensional record of surface current velocity every 20 min, with spatial resolution of about 1 km. The OSCR coverage during COPE-1 was somewhat larger than shown by the subsampled set of 12 gridpoints (filled circles) in Figure 1. [10] Since our objective is to describe barotropic tidal variability, all input data were analyzed for tidal content. HALLOCK ET AL.: TIDES NEAR THE CHESAPEAKE BAY ENTRANCE 20-3 The three constituents, M 2, S 2, and O 1, the most energetic constituents in the model domain, were fitted to all data series by least squares, and tidal time series of the sum of these constituents were calculated. Although the N 2 constituent is of the same order as S 2 in this region, it cannot be separated from M 2 with the length of the available data records; hence we assume that N 2 energy (the ratio of N 2 to M 2 amplitude is about 0.2) is folded into the M 2 estimates. These tidal time series are used in all subsequent calculations. The tidal fitting is straightforward for the elevation sites and for the ADCP record after calculation of a depthaveraged time series. However, since the OSCR data represent only surface current, we must ask how representative they are of the depth-averaged flow. Figure 2 shows vertical profiles of ADCP tidal constituent ellipse parameters. Clearly, M 2 is dominant and all amplitudes are largely depth-independent. S 2 and O 1 show more change of ellipse orientation than M 2, particularly for O 1 near the bottom. Hence the use of a barotropic tide model is quite appropriate. The subset of OSCR points (Figure 1) was therefore selected to avoid the highly stratified outflow plume [e.g., Hallock and Marmorino, 2002], which flows southward along the coast, extending out about 10 km except during strong upwelling wind events. The selected OSCR records are thus considered to be representative of depth-averaged flow Historical Data Used for Validation [11] Current meter data were acquired during four deployments between May 1985 and March 1986, from the CBE area (W. Boicourt, personal communication, 1998). These records were depth-averaged (where more than one instrument was on a mooring) and fit with the tidal constituents. Principal standard deviations (PSDs) [Preisendorfer, 1988, Figure 2.1] were computed with reconstituted tidal series for comparison with model results. Similarly, PSDs were computed with tides based on records from five ADCP moorings deployed from early October to mid November 1997 and from one ADCP mooring deployed for about 10 days in summer 2000 in the same region as COPE-1. These data were collected as part of NRL s COPE-3 [Hallock and Marmorino, 2002] and COJET (D. Johnson, personal communication, 2001) experiments. 3. Model Description 3.1. Model Equations [12] The method is described in detail by Griffin and Thompson [1998]; here only the essential steps are shown. We assume that the study area (the model domain is the area depicted in Figure 1) can be adequately represented by the linearized, vertically integrated (shallow water) equations, u t fv þ gh x ¼ ku H v t þ fu þ gh y ¼ kv H h t þ ðuhþ x þðvhþ y ¼ 0; ð1þ Figure 2. Tidal ellipse parameters for COPE-1 ADCP record. (a) Amplitude (negative semiminor axis value indicates clockwise rotation of the current vector). (b) Orientation. where u and v are vertically integrated velocity components in the x (eastward) and y (northward) directions, respectively, and h is free surface elevation. H is water depth, f is the Coriolis parameter, and k is a linear bottom drag coefficient. Since only tides are considered, there is no direct external forcing term present. Instead, the model is effectively forced from the open boundaries through the assimilation of observational data in the interior of the model domain. [13] Boundary conditions are needed to control these equations where the ocean meets the land or an edge of the model domain. For land boundaries a condition of zero normal flow is used. For open ocean boundaries the condition is, n ¼ t pffiffiffiffiffiffi H gh h; ð2þ H where n is the normal component of velocity at the boundary and t is a specified normal flux at the boundary. The term proportional to elevation in equation (2) is a radiation condition which minimizes reflections of outgoing waves (positive sign for upper or right boundary) from the boundary [Thompson et al., 2000] Discrete Formulation [14] The equations are solved on a rectangular grid in x and y over uniformly spaced times. An Arakawa C grid with 20-4 HALLOCK ET AL.: TIDES NEAR THE CHESAPEAKE BAY ENTRANCE a size of M y by M x is used. The grid resolution is approximately 1.4 km for the bathymetry and 2.9 km for u, v, and h. Let S y =(M y 1)/2 and let S x =(M x 1)/2. The sizes of u, v, and h are then S y by S x +1,S y +1byS x, and S y by S x, respectively. Each of these gridded variables can be identified by a single index. Time steps are denoted by the index n = 1,..., N. All dependent variables, which include boundary velocities, are represented at time t n by the vector, Xn T ¼ ½ u 1n; u 2n ;...; v 1n ; v 2n ;...; h 1n ; h 2n ;... Š; ð3þ where the column vector X n, here represented by its transpose (indicated by the superscript T ), is of length M = (3M y M x M y M x 1)/4. The dynamical equations together with their boundary conditions, are then expressed as a matrix operator, D 1, that advances X n by one time step and a matrix operator, D 2, that incorporates the boundary forcing vectors, t n =[t 1n,t 2,n...]: X n ¼ D 1 X n 1 þ D 2 t n ; n ¼ 1;...; N: ð4þ [15] Observational data are represented as a sequence of vectors d n of length L. Each value of one of these vectors represents an observation at a particular location at time n. A measure of the mismatch between model solution and data over all measurement points is evaluated as a cost function, J ¼ 1 X N 2s 2 0 n¼0 ðax n d n Þ T WðAX n d n Þ; ð5þ where the diagonal elements of matrix W are weights used to nondimensionalize and adjust the relative influence of various data. Hence J is implicitly a function of all t n.in this study the weights set the influences so that a 0.5 cm s 1 prediction error in ADCP velocity has equal effect on J as a 1.0 cm/s error in OSCR data and a 3.0 cm error in surface elevation. Only the relative values of the weights affect the solution. The different weights used for the ADCP and OSCR velocities is based on the expectation that the ADCP measurements more accurately represent the barotropic tide than do the OSCR measurements. Different weights for velocity and surface elevation are chosen to enhance the effect of velocity measurements. A is an L by M matrix that performs bilinear interpolation between the grid points and the data locations. s 0 is an overall weighting factor to scale J. [16] In presenting results below, J is represented as a sum of contributions from different data types, thus giving a measure of the success in assimilating a particular type. For example, we can take J = J c + J h where J c and J h, each of the form of equation (5), are respective contributions from current and elevation data. [17] We select the normal fluxes, t, in equation (4) as control variables. The solution we seek minimizes the cost function, J, with respect to these control variables. Fluxes (rather than elevations) are chosen because they are easier to specify as forcing (K. Thompson, personal communication, 2000). The bottom friction parameter, k, is not explicitly included as a control variable but a series of model runs using k between ms 1 and ms 1 shows a relative minimum in the cost function, where J 5% of its initial value, for k ms 1. [18] In particular, transports across each of the open boundaries of the model domain are expressed as the sum of nonoverlapping boxcar functions with unknown amplitudes, giving 14 unknown time series to be determined by the assimilation. The boxcar functions group adjacent boundary fluxes together thus reducing model resolution with regard to the fluxes (radiation condition resolution is not reduced). The distribution is deliberately coarse since a finer resolution would not adequately constrain the model with the distribution of observations available for this study. For this same reason the unknown amplitudes are defined in 1.5 hour time steps rather than at the fine time steps needed to satisfy the CFL limit of the model. Amplitudes for the functions for times between these coarse time steps are determined by a temporal interpolation function (see, for example, equation 7 of Griffin and Thompson [1996]). The use of this interpolation function with 1.5 hourly data can adequately reproduce fluctuations at the S 2 frequency, the highest frequency considered in this study. There is a tradeoff between independent data input and control variable resolution. This issue is discussed in section Solution Equations [19] A solution for the assimilated fields that satisfies the dynamical equations and minimizes the mismatch with data can be obtained by finding a saddle point of the Lagrange function, L¼J þ XN l T n n¼1 ð X n D 1 X n 1 D 2 t n Þ: ð6þ Setting the derivatives of L with respect to the Lagrange multipliers (l) and model variables (X ) to zero leads to X n D 1 X n 1 D 2 t n ¼ 0; n ¼ 1;...; N ð7þ l n D* 1 l nþ1 þ 1 s 2 A T W T ðax n d n Þ ¼ 0; n ¼ N;...; 0; ð8þ 0 where equation (7) is just the dynamical equation (4), which the solution must satisfy exactly. Equation (8) is the adjoint equation (for l), where the matrix D* 1 is the adjoint of D 1, but for linear dynamics it is the transpose of D 1. This equation steps backward in time, calculating the Lagrange multiplier vectors, l n. The otherwise undefined vectors are assigned the values l 0 ¼ 0; l nþ1 ¼ 0; X 0 ¼ 0: ð9þ [20] Given a first guess for the control variables, t, the above system of equations can be solved, yielding values for the Lagrange multipliers. Setting the derivative of L with respect to the control variables to zero n D* 2 l n ¼ 0; n ¼ N...0: ð10þ Equation (10) allows the calculation of the derivatives of J with respect to t for this particular guess of t. A conjugate HALLOCK ET AL.: TIDES NEAR THE CHESAPEAKE BAY ENTRANCE 20-5 gradient technique is used to adjust the values of t from their first guess values using this derivative information. This procedure is repeated iteratively until convergence on the minimum of J has been obtained. For this study,

Search

Similar documents

Related Search

Transport Properties of Fluids Near the CritiTransport Properties of Fluids Near the Critithe strange description of fossil KSD-VP as AA Portrait Of The Artist As A Young ManA Vindication Of The Rights Of WomanThe Black Arrow: A Tale Of The Two RosesBen Hur: A Tale Of The ChristThe Moore-Penrose inverse for a sum of matriA description (in French) of some ethical issA reflection of the ethical obligations of th

We Need Your Support

Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks

SAVE OUR EARTH

We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

More details...Sign Now!

We are very appreciated for your Prompt Action!

x