Description

1
3D Numerical Study of Hydrodynamic Forces on Surface-Piercing Inclined Marine
Piles
Mostafa Amini Afshar
1
, Mohammad javad Ketabdari
2
, Sabagh Yazdi
3
1- Hormozgan University, Department of Civil Engineering
2- Amirkabir University of Technology (AUT), Faculty of Marine Technology
3-Khaje Nasir University, Department of Civil Engineering
Abstract
Inclined pile is a structural element which is widely used in variety of structures to
confront the lateral forces in

Categories

Published

All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.

Share

Transcript

1
3D Numerical Study of Hydrodynamic Forces on Surface-Piercing Inclined Marine Piles
Mostafa Amini Afshar
1
, Mohammad javad Ketabdari
2
, Sabagh Yazdi
3
1- Hormozgan University, Department of Civil Engineering 2- Amirkabir University of Technology (AUT), Faculty of Marine Technology 3-Khaje Nasir University, Department of Civil Engineering
Abstract
Inclined pile is a structural element which is widely used in variety of structures to confront the lateral forces in marine environment. Although study of wave forces on piles dates back to few decades ago, however many of these studies mainly focused on wave interaction with vertical piles. These results then roughly extend for inclined piles. This study focus on numerical estimation of the hydrodynamic wave forces on a Surface-Piercing Inclined Marine Pile to determine the hydrodynamic coefficients. A set of tests performed on cylinders with different inclined angles in a numerical wave tank with a piston-type wave maker using Flow 3D. History of applied forces resulting from the model run and also Morison equation are used to extract hydrodynamic drag and inertia coefficients. The results showed that these coefficients are very sensitive to wave characteristics and pile inclined angles so that the tables in classical offshore texts mostly overestimate or underestimate these important factors. Keywords: Inclined Marine Pile, 3D Analysis, Numerical simulationl 1 Introduction The landmark in the study of wave forces on piling dates at about 1950, (Morison et. Al, 1950), a research in which Morison found a particular relationship between the force and kinematics of the wave. One of the important assumptions in his work was that the characteristics of wave such as velocity and acceleration had not been influenced by the presence of the body in the medium. It should be noted that wave force due to diffraction can not be estimated using the Morison equation. Of the pioneering study of diffraction is that of Havelock (1940) in which he developed a linearized diffraction theory for small–amplitude water waves in deep oceans. Nonlinear simulation of wave-structure interaction problems in three dimensions was first presented by Issacson (1977) in a work where the interaction between waves and offshore structures was studied. Estimation of wave load on spar platforms was done numerically via a particular method that is called, VOF (volume of fluid) by Kleefsman and Veldman (unknown). They used this method to simulate the free surface displacement of the water. Sunder ,et al (1998) conducted an extensive experimental study of forces due to regular waves on inclined cylinders in which they derived coefficient of drag and inertia for inclined cylinders of various inclinations. He examined the relationships between hydrodynamic coefficients, inertia and drag coefficient, and the dimensionless Keulegan-Carpenter parameter, and finally found that hydrodynamic coefficients change dramatically for Keulegan-Carpenter numbers up to 4. Another experimental study for inclined cylinders that influence of various inclinations on the wave force is demonstrated, is that of Anandkumar et.al
1
M.Sc in Marine structures
2
Assistant Professor
3
Assistant Professor
2 (1994), in which by conducing a wave flume test they measured dynamic pressures around cylinder and finally obtained the resulting net forces. Effects of random seas also studied by Sunder et al (1999), an experimental study in which dynamic pressures on inclined cylinders have been measured. 2 Governing Equations In this study applying the finite difference method, continuity and Momentum equations have been solved. The differential equations can be expressed in term of Cartesian coordinate, X, Y, Z. All equations are formulated with area and volume porosity functions. This formulation called
FAVOR
(Fractional Area/Volume Obstacle Representation method) and is used to model complex geometric regions. I this method obstacles can be defined by zero volume porosity regions. Generally in this method area and volume fractions are time independent. However these quantities may vary with time when moving obstacles are being modeled. The continuity and also Navier-Stokes equations underlie the basis of numerically simulation of wave tank in this study as follows:
( )
( )
( )
0
=∂∂+∂∂+∂∂+∂∂
z y xF
wA zvA yuA xt V
ρ ρ ρ ρ
(1)
++∂∂−=
∂∂+∂∂+∂∂+∂∂
x x z y x
f
f G x pl zuwA yuvA xuuAV lt u
ρ
++∂∂−=
∂∂+∂∂+∂∂+∂∂
y y z y x
f
f G y pl zvwA yvvA xuuAV lt v
ρ
(2)
++∂∂−=
∂∂+∂∂+∂∂+∂∂
z z z y x
f
f G x pl zwwA ywvA xwuAV lt w
ρ
In these equations
z y x
GGG
,
,
are body accelerations, and
z y x
f f f
,, are viscous accelerations that for a variable dynamic viscosity
µ
are as follows:
()()()
f x x xx y xy z xz
V f A A A x y z
ρ τ τ τ
∂ ∂ ∂= − + +
∂ ∂ ∂
()()()
f y x xy y yy z yz
V f A A A x y z
ρ τ τ τ
∂ ∂ ∂= − + +
∂ ∂ ∂
()()()
f z x xz y yz z zz
V f A A A x y z
ρ τ τ τ
∂ ∂ ∂= − + +
∂ ∂ ∂
Fluid configuration is defined in terms of a volume of fluid (VOF) function, F(x y, z, t). This function represents the volume of fluid per unit volume and satisfies the following equation:
()()()0
y zF
F lFA u FA v FA wt V x y z
Χ
∂ ∂ ∂ ∂+ + + =
∂ ∂ ∂ ∂
(3)
3 where
X
A
,
Z Y
A A
, denotes fractional areas at the centers of cell faces normal to the
x,
y
and
z
direction respectively.The basic procedure for advancing a solution through one increment in time,
i
δ
, consists of three steps: Explicit approximations of the momentum equations, Eq. 2, are used to compute the first guess for new time-level velocities using the initial conditions or previous time-level values for all advective, pressure, and other accelerations. To satisfy the continuity equation ( Eq. 1) when the implicit option is used, the pressures are iteratively adjusted in each cell and the velocity changes induced by each pressure change are added to the velocities computed in step 1. Iteration is needed because the change in pressure needed in one cell will upset the balance in the six adjacent cells. In explicit calculations, iteration may still be performed within each cell to satisfy the equation-of-state for compressible problems. Finally, when there is a free surface or fluid interface, it must be updated using Eq. 3 to give the new fluid configuration. Repetition of these steps will advance a solution through any desired time interval. At each step, of course, suitable boundary conditions must be imposed at all mesh, obstacle, and free-boundary surfaces. 3 Wave tank simulation One of important aspects in simulating a wake tank is to specify its boundaries. The boundary conditions considered in this study is as follows: 3.1 K.F.S.B.C: Kinematic Free Surface Boundary Condition: this boundary condition relates the free surface velocity to its elevation. Linearized K. F. S. B. C for a wave type flow based on potential theory is as:
t z
∂∂=∂∂−
η φ
On 0
=
z
The numerical method that is used in this study deals with kinematic free surface boundary condition by the velocities that are set on every cell boundary between a surface cell and an empty cell. 3.2 D.F.S.B.C: Dynamic Free Surface Boundary Condition. Lineaeized dynamic free surface boundary condition for wave type flow, based on potential theory is as:
t g
∂∂=
φ η
1
on0
=
z
. As we mentioned earlier, the numerical method is capable of modeling the free surface via the volume of fluid function (VOF) approach. The function represents fluid and void regions by 1 and 0 respectively. Dynamic free surface boundary condition is applied by assigning a uniform pressure to void region (F=0). 3.3 B.B.C: Bottom Boundary Condition. That specifies zero vertical velocity on the impervious bed, that based on the potential theory is as:
0
=∂∂−
z
φ
At
h z
−=
,in which
h
is water depth. 3.4 No-Flow condition on cylinder surface. For an impermeable cylinder is as:
0
=∂∂−
n
φ
on cylinder surface. In which n is the vector normal to the surface. B.B.C and also no-flow condition on cylinder surface is applied to the wave tank by setting the normal velocity to zero. This is done by blocking the surfaces of bed and cylinder that otherwise are open to flow. 3.5 R.B.C. Radiation Boundary Condition.
4 For the practical reasons, both experimental and numerical wave tanks have to be of limited extent and inevitably we must truncate some boundaries of the wave tanks and as a result of this fact , waves have to propagate in a limited region. Something of vital importance here is to prevent the outgoing waves, which are passing these truncated boundaries, from reflecting back into the wave tank. This is exactly the case in actual situation in which the waves reflecting away from the body never back towards it. In experimental wave tanks the problem overcome by using wave dissipaters, in numerical wave tanks, this is done via applying
Radiation Boundary Condition
. Based on the potential theory this condition is as:
01
=∂∂=∂∂
t C n
φ φ
Where
C
wave celerity and
n
is the vector normal to the boundary. The present numerical method applies this boundary condition as:
0
=∂∂+∂∂
xQC t Q
In which
Q
is any flow quantity. 3. 6 Wave Boundary Condition. Generally one side of wave tanks devoted to wave creation. In experimental studies this is done by wave makers. Based on the type of the wave that is wanted, there is variety of wave makers. In theoretical studies we can apply this boundary condition by specifying a particular velocity to one side of the wave tank. We use here of a piston type wave maker by applying the following displacement and velocity specifications:
t S x
ω
sin2
=
,
t S t zu
ω ω
cos2),,0(
=
In which
S
is stroke of the wave maker 4 Specifications of the tests. A set of 24 tests 4 carried out, in which angle of inclination of the cylinder varies up to 45 degree. For each angle the tests is repeated for four different
KC
, that are 4.3, 2, 0.87 and 0.5. Following specifications considered here to conduct the tests: Wave tank:Height: 100 cm, Length: 270 cm for cylinders with 0º, 15º,20º,30º inclination, and 320 cm for 40º and 45º inclination, Width: 100 cm, Water depth: 30 cm Side view and plan view of the wave tank that used for
45
=
θ
º is shown in fig. 1. Wave maker located at
0.5
z
=
and has the freedom to move between
2020
≤≤−
z
. At the distances more than three times of the water depth from the wave maker, standing waves decayed virtually ( Dean and Dalrymple, 1992) Cylinder: Diameter: 30cm Position: (0
=
θ
º 145
=
z
cm), (15
=
θ
º 130
=
z
cm), (20
=
θ
º 150
=
z
cm), (30
=
θ
º
150
=
z
cm), (
40
=
θ
º
130
=
z
cm), (
45
=
θ
º
130
=
z
cm) Wave: Period: 1 sec for all tests. Piston stroke: Varies for each
KC
as: (
3.4
=
KC
5.17
=
S
cm), (
2
=
KC
10
=
S
cm), (
87.
=
KC
5
=
S
cm), (
5.
=
KC
3
=
S
cm) Finish time: The model is run up to 10 wave periods that is 10 sec. 5. Conducting the tests 24 distinct tests was carried out each of which having a particular
K
N
and
θ
. In these tests the focus was on forces applied to the cylinders in the
z
direction . Each run

Search

Similar documents

Tags

Related Search

Study of rituals and its impact on family cohON THE NUMERICAL SOLUTION OF FRACTIONAL PARTIstudy of MHD on flow problemsStudy of rearrangements on SteroidsPhd Thesis on Plays of Girish Karnad Study ofStudy on Dispersion of Air Pollutants on CoasComparative study of agripreneurship on youthArticle 50 Of The Treaty On European UnionStudy Of ReligionEmpirical Study of Literature

We Need Your Support

Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks

SAVE OUR EARTH

We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

More details...Sign Now!

We are very appreciated for your Prompt Action!

x